Models > JEW9627AAW > Instructions

JEW9627AAW Jenn-Air Oven - Instructions

All installation instructions for JEW9627AAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JEW9627AAW
1-15 of 167
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 88 of 101 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.

F1-1 code

  • Customer: charles from marstons mills MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 35 of 42 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.

Oven door doesn't completely close, light stays on

  • Customer: John from Harvard MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 27 of 43 people found this instruction helpful
I replaced the hinges on the door, it wasn't that hard to do, a couple of minor things I had to overcome. But the new hinges still don't close the door completely. The light still comes on. I don't think the springs in the hinges are strong enough.

I asked for a particular part number in my order, the sales rep, said that wasn't the correct part number, and gave me a different part number. Now I'm not sure if the sales rep gave me the correct part or not.

Either way, I spent money for new hinges, and my own labor, and I still have the same problem.

I've placed calls with Jenn-air, and local technicians, but so far, do not have a solution to my problem. So overall, I'm not very happy.

Anyone got any ideas?

Dim clock and oven display lights

  • Customer: Rollin from Petaluma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 19 of 21 people found this instruction helpful
Turn off power to oven. open top oven door and remove the four screws holding the display unit in place. Pull out on the bottom and lift up. Disconnect the wires and lay unit on counter.
Remove the four screws holding the clock display and replace with new part. Reassmble. Ahhh lights. Pray that you new unit doesn't burn out in four years. The end.

Repeated oven temperature sensor fault codes.

  • Customer: David from Arlington VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 18 of 20 people found this instruction helpful
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.

Oven door wouldn't close completely

  • Customer: William from Statesville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 17 of 20 people found this instruction helpful
Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs aren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.

Oven wouldn't heat the right temperature (you would have to add 100 degrees on to it)

  • Customer: Claudine from Bethlehem PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 15 of 15 people found this instruction helpful
Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.

baking element burnt out

  • Customer: Kathy from Powder Springs GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 18 people found this instruction helpful
It was so easy....a cave man could do it.

Power off to oven, 2 screws, swapped the elements, 2 screws back in. Keep the original screws. The only delay we had was the right screw was a little hard to "start".
Once we had it tightened up, we turned the breaker back on and wah la....we had our oven back!

Shipping was much faster than expected!

LED lights faded and eventually disappeared

  • Customer: Gorden from Silver Spring MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 11 of 11 people found this instruction helpful
First, I turned off the circuit breaker to the double over.
Second, I opened the oven door. At the top of the frame, underneath the panel are four screws (not evenly spaced) that I removed. I held onto the glass control panel, not wanting it to come down when I removed the screws, but this was unnecessary as there is a ridge in the back to keep it in place.
Third, I lifted out the glass control panel. There are two sets of wires going from the oven to the control panel. One set of wire connects in two places (three connections in total).
Fourth, I simply disconnected these wires from the chips (lifting them off), trivial. They all have different connectors, so there is no chance of getting them mixed up. If you have never touched any new electronics and are completely unfamiliar with plugging wires on a chip, you may take note of the orientations of the connectors), but it is fairly dummy-proof.
Fifth, there are four screws holding the display in place. Used the socket wrench for these (they go through the holes you see on the side of the unit in the picture).
Sixth, reversed the last operation, screwing the new display in place on the removed panel.
Seventh, Some of the teeth on the connector of my new display were bent over. I bent these straight so the connector would go over them, and reconnected the wires, carefully(!)
Eighth, slipped the glass panel in place. When seated properly, it does not shift.
Ninth, secured panel with the four initial screws.
Tenth, turned on the circuit breaker.
Eleventh, was shocked by how bright the new LED was!

defective oven sensor

  • Customer: sean from easthampton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 15 people found this instruction helpful
Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

Oven Door hinge is broken

  • Customer: Hugh from Hopewell NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
One oven door hinge spring was broken. I ordered two hinges to complete the repair.
The repair could not have been easier. I removed the door from the oven an unscrewed the outer frame of the door from the inner door assembly. I unscrewed the old hinge assembly and replaced them with the two new hinges.
I set the door back on the oven and replaced the oven door retaining hardware.
After replacing the retaining hardware, I removed the temporary shipping pins that keep the spring assembly static. Very important: don’t remove these hinge pins until the door is on the oven an the oven retaining hardware is secured.

Code said we needed a sensor

  • Customer: Janice from Portland OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

Oven Door wouldn't fully close and light stayed on.

  • Customer: Jeff from Fremont CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
Remove oven door by removing chrome flat plate that holds the hinge in place (one screw at each hinge) and LIFT door off oven. There is a hole in the hinge that you can stick a small nail through to hold the hinge in the "partially open" position for easier removal and replacement of the door (I didn't know this until I received the new hinges, which have a removeable pin in the hole.) After door is off, remove three screws each, on the top and bottom of door, to remove the back half of door and expose the hinges. Remove one screw from bottom of door that holds bottom of hinge in place. Lift out hinge bottom and unhook top of hinge. Reverse process to reassemble. Remove small pins by opening oven door fully. The new hinges did solve the problem. You have to order two hinges for each door. They are NOT sold as pairs.

After self cleaning the oven received an error code telling me the sensor was bad.

  • Customer: Christine from Davie FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

Rubber gasket failed due to age

  • Customer: Mary from Woodland WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 14 people found this instruction helpful
I learned that I could clean the window in the oven door. In taking it apart I saw that the gasket had fallen into the oven door. I found the part online, it arrived in three days. I removed the metal part of the door, removed what was left of the old gasket and put in the new one. Put the metal part of the door back on, and it was as good as new.
All Instructions for the JEW9627AAW
1-15 of 167