Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JES9900BAB > Instructions

JES9900BAB Jenn-Air Range - Instructions

All installation instructions for JES9900BAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES9900BAB
76-90 of 144
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Filter Worn Out

  • Customer: Thomas from Berlin, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Remove cover and install

Oven temperature lagging set temperature by almost 100F

  • Customer: William from Edgewood, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

needed new grease filter

  • Customer: Barbara from Hubert, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)

Varying heat

  • Customer: Kimbel from Rhoadesville, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

not heating/kicking oven off

  • Customer: Kevin from Virginia, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

Oven would not work

  • Customer: george from San Antonio, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 2 people found this instruction helpful
Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

replaced the current warn-out grease filter

  • Customer: Joseph from East Greenwich, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
removed the old by pulling it out of track and replaced it with the new filter

The filter in the grill section of my stove fell apart.

  • Customer: Beth from Dunkirk, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I simply removed the old filter and replaced it w/the new filter. It came in record time and I'm very pleased w/the service I received.

I Destroyed My Grease Filter In The Dishwasher And It Just About Disintergrated.

  • Customer: Rosetta R. from Jamaica Plain, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 6 people found this instruction helpful
I just had to drop the grease filter into the slot. It took less than a second. But what I am really pleased with is that it took less than a day and a half to get the part. I ordered it on thursday morning. It was shipped on thursday afternoon and in my driveway by friday noon!!! Wow!!! How great was that!!!!!! The fastest service I've every had for anything!! Bravo!!!!!!!! To all your workers!!!!! Rrm

the original grease filter was worn and falling apart

  • Customer: Barbara from Medfield, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Removed the old filter from the top of stove and put the new one in. Took about 10 seconds.

Bake element burn out

  • Customer: Richard from Jericho, VT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I Goolged my Brand of Appliance. I picked the catagory that mostly described what I was looking for. At PartSelect there was a diagram of my oven model with every part shown and described. It even showed the end pieces that were not visible when the oven door was opened. I removed the two screws at the end of the element, pulled the old element out and removed the spade clips from the wiring harness. I replaced the burnt out element with the new one I ordered. It was delivered to my home within two days.

Oven door was locked, couldn't set oven temps

  • Customer: William from Nashville, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

1 Pane of Inner Safety Glass

  • Customer: Mary from Bellefonte, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.

Oven wouldn't heat

  • Customer: Clinton from Lander, WY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the screw in each end of the element, remove the old element, install the new one and put screws back in.

Screws on the door of the dishwasher were very loose.

  • Customer: Kathryn from Carol Stream, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
All Instructions for the JES9900BAB
76-90 of 144