Models > JES9800AAW > Instructions

JES9800AAW Jenn-Air Range - Instructions

All installation instructions for JES9800AAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES9800AAW
286-290 of 290
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The inner glass shattered when the oven was in the clean mode

  • Customer: Charles from Sulphur LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.

Maytag range had "F3" code display, oven would not work.

  • Customer: phillip from Farmington NM
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

Oven would not heat above 200 degrees when set at 350 degrees. Element would not get hot (not red).

  • Customer: Douglas from Fenton MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off power (at breaker panel). Pull out range from wall and unplug electrical cord from outlet. Remove retaining screw at each side of element. Slowly pull out element from back of oven to expose electrical connector. Use pliers to pull connector apart (do not pull on wire). With element disconnected, measure resistance between the two ends of the element. Found infinite resistance or open circuit. Ordered replacement part and measured new part to be 20 ohms. Installed new element by pushing on connectors to new element. Carefully push new element into oven back wall and secure with the 2 screws. Plug electrical connector into wall socket and push range back to the wall. Turn on breaker switch. Turn on oven to verify fix. Note: Confirm there is voltage on both legs of wall socket for 220 volts which will confirm the breaker at panel is functioning. This can be done before removal of element from the range.

Oven would not heat on Back Cycle

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

The dual surface burner would come on and go off intermittently when the switch was turned to off.

  • Customer: Gary from Bend OR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.
All Instructions for the JES9800AAW
286-290 of 290