Models > JES9800AAW > Instructions

JES9800AAW Jenn-Air Range - Instructions

All installation instructions for JES9800AAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES9800AAW
271-285 of 290
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

cleaner

  • Customer: Mary from Duarte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Heating element went out.

  • Customer: RITA from SODDY DAISY TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did it within minutes. Very easy.

Broken inner glass

  • Customer: Joe from Bronx NY
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

Upper oven shut down after reaching temperature

  • Customer: Earl from Globe AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Heating element in oven quit working

  • Customer: Nathan from Nashville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Our heating element ended up breaking from age and use. The repair was extremely easy: turn off breaker to oven, unscrew two screws holding in the heating element, pull it from the unit and detach the element from the electrical wiring. Once this is completed just perform the steps in reverse. The part arrived very quickly from PartSelect, arriving in just 2 days with the standard shipping. I am very pleased with my interaction with PartSelect.

heating element burnt out and broke

  • Customer: Darlene from Dingmans Ferry PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off power source before beginning.Unscrew the bracket attached to the back of the oven,carefully pull the heating element forward, exposing the connecting wires. Push any insulation back into wall while holding wires securely.Remove connection with needle nose pliers.Pull wires in wall from each side as far out as possible.Connect heating element to each wire carefully push back element lining up with holes in back of the oven. Attach screws snuggly and you're ready to use.

grease filter had holes

  • Customer: Lavonne from Hutchinson MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
throw the old one in the garbage, drop in the new one. It is about 3/4" narrower than the one that came with the stove but still covers the down vent adequately

Rear burner was not functioning

  • Customer: Michael from Port aransas TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
used a multimeter to determine that power was going to the surface burner infinite switch. then determined that power was not going from the output side of the switch to the burner element. Turned power to range off at the breaker box. Removed eight screws total on range top, four on the cartridge side, two located on back of control plate where the downdraft vent is located and two on the double fixed burner side. Raised the range top to gain access to the infinite switch assemblies. Removed to TORX head screws retaining the infinite switch and then disconnected the five wires on the bottom one at a time, making sure to replace in the exact location on the new switch. Installed TORX screws in the new switch and installed all screws back into range top. reinstalled cartridge and burners and turned power back on. Tested rear burner and all functioned properly.

WHEN WE TURNED ON THE OVEN THE TEMP. READING WENT UP TO 425 AND BEEPED BY NO HEAT

  • Customer: DAVID from Cape Coral FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back WOW saved me $500. from buying new and $150. for service call

My convection oven fan had stopped working, so I replaced it.

  • Customer: Christopher from Ithaca NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I partially opened the oven door and lifted the door off its hinges. Then I removed the oven racks. Using a Phillips-head screwdriver, I unscrewed the six screws holding the fan cover plate and the fan in place, unscrewing the uppermost screw last. Unfortunately, I did not mark the fan cover plate in its precise location with respect to the back oven wall. The combined fan and fan cover plate assembly fell of the back oven wall. I easily unhooked the electrical connection of the fan, which is a simple plastic connector, removed the old fan, and connected the new fan's electrical connector to its connection, making sure that the color coded parts of each connector aligned. Then the fun began. Because I hadn't marked the fan cover plate with respect to the back oven wall, I had to figure out how the fan cover plate screw holes aligned with the back oven wall screw holes. Once I figured that out, I had to figure out how the fan aligned with the fan cover plate. Having bad knees, I could only kneel on a doubled pad for short periods of time, so the process took awhile. I found it impossible to prop the two pieces together while simultaneously screwing in the screws. Eventually I aligned the fan with the fan cover plate and partially screwed the two together in several places, with the screws just barely penetrating past the fan cover plate. Then I was able to hold the combined assembly in place and screw the screws into the back oven wall.

Could not detach wires on each end of the element.

  • Customer: Marlene from Merchantville NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Instructions did not included need to pull oven from wall to access connections. A pro knew what to do, was finished in 10 min!

Replace heating element in oven

  • Customer: Vallie from Morrice MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled out broken element, took out screws, put in the new part and inserted it.. My son had to do it though. Easy for him

Bake element broken.

  • Customer: Maryann from Seatac WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Super easy; pulled out broken element and pushed in new element. Wonerful service, communication, shipping. Received part in Seattle and mailed it to Hawaii installed without a hitch. Thank you

change oven sensor

  • Customer: Lloyd from Eau Claire WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed provided video

super easy

  • Customer: Joanne from West Falls NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just followed the instructions in the video!! A repair service was going to charge $95.99 just to walk in the door!!I I just ordered the igniter part. Watched the video and I know I can do that too!! I have only had one self igniting burner for years - didn't want to pay for a service call. Love your company!! Thank you!
All Instructions for the JES9800AAW
271-285 of 290