Models > JES9800AAS > Instructions

JES9800AAS Jenn-Air Range - Instructions

All installation instructions for JES9800AAS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES9800AAS
286-300 of 302
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

super easy

  • Customer: Joanne from West Falls NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just followed the instructions in the video!! A repair service was going to charge $95.99 just to walk in the door!!I I just ordered the igniter part. Watched the video and I know I can do that too!! I have only had one self igniting burner for years - didn't want to pay for a service call. Love your company!! Thank you!

The inner glass shattered when the oven was in the clean mode

  • Customer: Charles from Sulphur LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.

Maytag range had "F3" code display, oven would not work.

  • Customer: phillip from Farmington NM
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

Oven would not heat above 200 degrees when set at 350 degrees. Element would not get hot (not red).

  • Customer: Douglas from Fenton MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off power (at breaker panel). Pull out range from wall and unplug electrical cord from outlet. Remove retaining screw at each side of element. Slowly pull out element from back of oven to expose electrical connector. Use pliers to pull connector apart (do not pull on wire). With element disconnected, measure resistance between the two ends of the element. Found infinite resistance or open circuit. Ordered replacement part and measured new part to be 20 ohms. Installed new element by pushing on connectors to new element. Carefully push new element into oven back wall and secure with the 2 screws. Plug electrical connector into wall socket and push range back to the wall. Turn on breaker switch. Turn on oven to verify fix. Note: Confirm there is voltage on both legs of wall socket for 220 volts which will confirm the breaker at panel is functioning. This can be done before removal of element from the range.

Oven would not heat on Back Cycle

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

The dual surface burner would come on and go off intermittently when the switch was turned to off.

  • Customer: Gary from Bend OR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.

Oven element started getting hot spots and then just failed.

  • Customer: Timothy from Alfred Station NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply remove the two screws in the back and carefully work the element out taking care not to pull the wires off. I left the oven door on which made access somewhat awkward reaching in. Remove wire clips and install new element in reverse. So easy even a caveman could do it.

Range had an F-2 code on the control panel

  • Customer: Greg from Frederick MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

bottom element sparked out and no longer heated

  • Customer: dan from LaCrosse WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
unplugged the oven from the 220 volt receptacle. Removed the wire shelves. Unscrewed the two screws holding element to rear of oven. (I didn't know at this point to pull the wires through from the back so I took the back panel of the oven off and unplugged the connectors from the rear). Measured the defective element, ordered, and two days later I reversed the process when the package arrived in the mail. . quite simple. I love it when I can fix something myself. And by fixing, I actually mean "replacing".

Oven would overheat

  • Customer: MARK from roseville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

lower baking element burned out

  • Customer: Jim from Three Rivers MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
followed you tube instructions. Very helpful feature. thanks

Bottom bake element was burned out and no longer heating.

  • Customer: Paul from Mooresville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove both oven racks. Remove the screw that is on each side of the element holding it in. Pull the element out and disconnect the wire on each side of the element.Remove the bad element and replace it with the new element. Connect the wires to the new element and gently push the element back into place. Put the screws back into place and tighten. Replace the oven racks into oven. Turn oven onand verify that the element is heating. Repair is comlete.

F5 fault code kept appearing

  • Customer: Louis Rodriguez from Granbury TX
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

I had a power serge and it burned the Plug at the termial block and melted a few wire.

  • Customer: Robin from Vanderbilt PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

the grease filter was no longer usable from too many washings

  • Customer: Rose from North Kingstown RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took it out and dropped in the new filter. Total time about 2 minutes
All Instructions for the JES9800AAS
286-300 of 302