Models > JES9800AAB > Instructions

JES9800AAB Jenn-Air Range - Instructions

All installation instructions for JES9800AAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES9800AAB
256-270 of 302
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

switch on top of stove

  • Customer: James from Beaufort SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
James is an electrician so he istalled the part himself

Oven would not heat

  • Customer: Claude from Lakewood OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

The lower (baking) element burned out.

  • Customer: Timothy from Helena AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I'm the world's worst handy man, but after watching the repair video on PartSelect I determined I might could do this repair. I ordered the part and replaced the element in less than 10 minutes! I also saved $160.00 by doing it myself!

Oven would not program and would shut down

  • Customer: Sreve from Deland FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

F1 Fault Code - Replace the Temperature Sensor

  • Customer: Dennis from Tampa FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

Rear butner no longer worked after liquid was spilled on range.

  • Customer: Paul from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just followed the instructions on this site... :) Unscrewed the front, removed old unit taking care of which wires went where, put in new unit. Voila.

Burner was very hot regardless of setting

  • Customer: David from Woodland Park CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.

Bottom Range Bake Element.

  • Customer: Debra from Marshfield WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I am a 60 year old women and I was so amazed that this was so easy, Except for whom ever put in striped screw before, got that out with a pliers. Thanks for your video online. Beautiful.

the bake element had a portion burned almost completely through

  • Customer: David from North Haven CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. turned off the breaker delivering power to the oven. 2. removed the grates. 3. unscrewed the 2 screws holding the element in place and gently pulled the2 ends of the element from the rear of the oven. 4. disconnected the 2 power connections from the element being careful not to have them slip back into the insulation at the rear of the oven. 5 removed the element and connected the new element to the power sources - this was the most difficult task, with little wire extending from the back of the oven it required delicate handling and certainty that the connection was solid. 6. slid the 2 prongs of the element into the rear of the oven. 7. installed the 2 screws. 8. replaced the grates.

Bake element was broken and needed to be replaced.

  • Customer: Carlton from Media PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the accompanying video on the website. Very glad I did as the key thing to remember when replaceing the bake element is that the connecting wires ARE VERY SHORT and can easily snap back inside the element lead hole in the back of the oven. Lead on the left side had a small amount of play but the right side element wire was extremely short and "snapped" back into the hole. I had to use needle nose pliers to pull it back through. Just take your time and keep your fingers on the leads as best you can.

burnt out bake element

  • Customer: KENNETH from TONOPAH NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The bake element repair itself was very easy and straightforward. The difficulty and extra time involved relates to improper wiring of the electrical circuit the range plugged into. A previous homeowner had apparently taken a shortcut when repairing a faulty di-pole circuit breaker and routed one side of the 240v circuit through a separate single-pole breaker which is a blatant electrical code violation. After replacing the faulty di-pole breaker and wiring the circuit properly the bake element repair was simple and the oven is working great. While most DIY folks will not run into this same problem with an improperly wired electrical circuit it pays to be cautious. I relied on the di-pole breaker to cut power to the oven during the repair but because one side of the circuit had been rerouted I received a nasty shock. Please do what I failed to do originally: unplug the range/oven at the wall before making the repair. And if you suspect improper wiring of the 240v circuit, please consult an electrician as it is a dangerous situation.

My oven was not holding temperature.

  • Customer: Anthony from Acworth GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

the bake element was broken

  • Customer: SHEILA from EAU CLAIRE WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I called my son, left the part, two screw drivers out, went to work, came home and was able to use my oven again! It couldn't have been easier and I made him some zucchine cake as a thank you for doing the job! It was easy to order and pay for the part online, get the part within a week and I was back in business. Thanks for being available to make getting the part a no-hassle experience.

Element went out and replaced the seal in the door

  • Customer: Nancy from Oakland OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The repair would have been very easy, except this oven has a factory defect with wiring for the element on one side. The element should just plug in after removing 2 screw. The wiring on one side is too short to plug into the element without the assistance of something like a wrench with a bent long nose, hence the the surgical clamp. The seal, for cleaning, is really easy to replace, It just snaps in to designated holes.

needed to replace the grease filter

  • Customer: Nancy from laveen AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I lifted the grill off; took the old grease filter out and threw it away; placed the new filter in the well; put the grill back on. Wallah!!! just like new.
All Instructions for the JES9800AAB
256-270 of 302