Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JES8850BCB

JES8850BCB Jenn-Air Range - Overview

Get Parts and Repair Help for JES8850BCB

If you know the range repair part you need, you can browse the list of all parts on the JES8850BCB, or you can search by name or part description. You can also find your part by where it is located on the JES8850BCB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for JES8850BCB parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$29.74

Long Oven Sensor

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the int...

Order within the next 57 mins and your part ships today!
$3.02

Screw

This screw is sold individually.

Order within the next 57 mins and your part ships today!
$18.51

Burner Knob

Sold individually. This knob accepts a D-shaped shaft.

Order within the next 57 mins and your part ships today!
$51.11

Oven Rack

This is a replacement oven rack and it is designed for use with ranges and ovens. This is a genuine OEM replacement part. The rack provides a level and stable surface for cookware inside of your appliance. Installing the new rack is simple, you slide it into the pre-existing tracks in your oven. It measures approximately 23 inches wide by 16 inches deep. This replacement part is made of metal and it is sold individually.

Order within the next 57 mins and your part ships today!
$44.96

Door Gasket

The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Bef...

Order within the next 57 mins and your part ships today!
$19.73

Terminal Block

This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.

Order within the next 57 mins and your part ships today!
$18.41

Control Knob

Sold individually. This knob accepts a D-shaped shaft.

Order within the next 57 mins and your part ships today!
$66.33

Inner Door Glass Pane

Glass only.

Order within the next 57 mins and your part ships today!
$18.41

KNOB FLEX

Sold individually. This knob accepts a D-shaped shaft.

Order within the next 57 mins and your part ships today!
$47.42

Infinite Switch - 6"

Order within the next 57 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 118 of 137 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

F1-1 code

  • Customer: charles from marstons mills, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 52 of 67 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will ... read more

Needed to replace oven door gasket.

  • Customer: Lori from Scottsdale, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 48 of 58 people found this instruction helpful
First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum. read more