This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
$10.58
In Stock
Order within the next 12 hrs and your part ships today!
This is the rotating ring assembly for your microwave. It rests under the glass tray, and allows it to rotate so your food can cook evenly. If you notice that your food is not cooking evenly or if the...
$22.53
In Stock
Order within the next 12 hrs and your part ships today!
This part is the replacement high-voltage diode for your microwave. It is approximately 3 inches long and is sold individually. The high voltage diode is an electrical current control device inside yo...
$8.54
In Stock
Order within the next 12 hrs and your part ships today!
This part is the replacement light bulb for your microwave. This bulb is 125 volts and 25 watts. It should come on automatically when you open your microwave door, or if the microwave is running. If y...
$11.60
In Stock
Order within the next 12 hrs and your part ships today!
Order within the next 12 hrs and your part ships today!
Questions And Answers for JES2051DN3BB
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fatima
December 30, 2019
Why does it keep jumping on and off while trying to use.
For model number JES2051DN3BB
Hello Fatima and thank you for writing.
Microwave to shut down and back on while in use are usually faulty internal fuse PS239525 or defective diodes PS1481239. We hope this helps. Please contact us anytime if you require further assistance.
The wave guide cover for model JES2051DN3BB does not have a sheet of silica behind it there is only the plastic wave guide cover for this model. Should a sheet of wave guide silica be placed behind the plastic cover as a wave guide shield?
For model number JES2051DN3BB
Hello Mike, thank you for contacting us. In this model, there is no sheet of silica. You only need to install a plastic waveguide cover for this model. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic
... Read morerowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Remove microwave outer cover. Turn on side & locate the upper & lower door switches. Better to replace in pairs even if one is ok. Remove the wire harness to each switch. Then replace switch and re connect the wire harness. Re attach outer cover and test to see if that solved the problem. If so then well done!!