Models > JED8430ADB > Instructions

JED8430ADB Jenn-Air Cooktop - Instructions

All installation instructions for JED8430ADB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JED8430ADB
61-75 of 77
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Original fan knob was broken

  • Customer: Bill from Newburgh IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Repair was simple thanks to feedback from this site.

1 burner wouldn't work, and caused the breaker to trip

  • Customer: Jeff from Houston TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the glass top and replaced the switch unit successfully. Hardest part was removing the unit from the countertop and bracing the base with a 4x4.

front burner would not heat

  • Customer: Jack A from Biloxi MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

Three of four burners were inoperable

  • Customer: David from Woodbridge VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was a repair project on a Jenn-Air built-in stovetop, which I had trouble finding instructions on how to disassemble. My particular problem was that three of the four burners had no temperature control. They were either on high or off - no such thing as simmer. This is opposite the problem described as a normal indicator of burner control failure. Usually the burner just goes dead. The hardest part of the repair was accessing the metal plate the burner controls are mounted on. First, I flipped the circuit breaker to the stovetop. It will shock the cr@#p out of you if you don't (I have experience from poking around down there without turning the power off). First, I had to remove the two burner inserts. The left one lifted from the top and the right one lifted from the bottom. Don't lift them past about 30 degrees. They are meant to lift up just enough to clear the tray well and then slide out. After removing the burner inserts, I was able to unscrew the eight fasteners holding down the stovetop rim. After removing this, I pulled out the trays underneath the burner inserts and put them aside without unscrewing the ground wires that attach them to the stovetop chassis. After removing the two screws holding on the active burner indicator lights, I was able to pull it up and lay it aside. Then I had to unscrew the two large brackets under the cabinet to loosen up the stovetop chassis so I could lift the front of it up an inch from the cabinet to enable me to unscrew two small metal screws that attach the metal plate holding the burner controls. After removing the two screws holding each burner control to the metal plate, I could unplug each of the five wires from the old controllers and plug them into the new controllers, in turn, before reattaching the new controllers to the metal plate. After repeating this procedure two more times, I reversed the process to reassemble the stovetop and voila, turned on the power and it worked perfectly. The result; a happy wife. For today.

Jenn-Air CCE3531B - Left Rear Dual Burner was Stuck On

  • Customer: Jeff from Kent OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Here is what I did with new switch (part#12002125) and it worked. Connect jumper to P1 and S1. Split the 2 red wires and put new spades on the ends, then put the red wire from left front switch on P2 and the other red wire from the right rear burner on 2. Blue goes to 4. Purple goes to 4A. Black goes to P1. Orange goes to S2.

replacement filter for jenn-aire

  • Customer: Fred from Mount Sinai NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
the filter fit because the scale in the photo allowed me to choose which one to buy!

Broken Fan Knob

  • Customer: Michelle from Fairfax VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This repair was extremely easy. I was able to lift off the broken fan knob with some pliers. The new knob easily fit and the new knob works like a dream!

cleaner

  • Customer: Mary from Duarte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Outside element of dual burner does not heat

  • Customer: Jimmie from Garden Ridge TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This Jennifer-Air cooktop has a black Schott Ceran surface. I unplugged the unit and disconnected the vent duct then removed the unit from the cabinet and shifted it 90 degrees to gain access to 10 screws that hold surface to body. Connections for replacement burner are slightly different than the original. I photographed wiring/connectors them removed the old burner. I removed mounting clips from old burner and installed them on the replacement (required two small tapping holes in aluminum case of replacement burner element). Installed new element and attached connectors (wires). No joy, outside element still did not heat - placed a dual element switch on order (have not received it yet). To be continued.

Nasty, clogged, old grease filter

  • Customer: Kim from Cottontown TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I carefully removed the disgusting old filter and took straight to trash. I then used my wet/dry vacuum to clean the rest of the loose debris from the area where the filter area is located. I used a clean, dry cloth to wipe the remainder of the material away and then carefully lowered the clean new filter down into it's new home. So easy, it took longer to type out these directions :)

Fan switch broken and needed replacing

  • Customer: Thomas from Glen Allen VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove blower assy. Lift cook top. Remove side screws on cooktop to cooktop frame. Lift glass cook top. Replace fan switch. Reverse disassembly.

The dual surface burner would come on and go off intermittently when the switch was turned to off.

  • Customer: Gary from Bend OR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.

instal duall switch and replacement burner

  • Customer: Fedor from Port Murray NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
1. remove corlan cover from base of unit 2. study original wire pattern of old burner and switch; write down pattern on paper 3 gently remove wires with needle nose pliers.4 replace with new burner and switch with color coded wire pattern copying the original wiring 5 reinstall corlan cover on base. remember to shutdown cooktop from either circuit breaker or fuse in order not to electrocute yourself while working remember wires are live until shut down from main source of power

surface burner failure

  • Customer: Gerald from Hot Springs Village AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.

Fan Knob didn't operate fan or retract

  • Customer: Cyril from Cincinnati OH
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Part is a new design. Had to remove all the housing for the old knob. Don't leave anything in the hole. A bit apprehensive, but it works great.
All Instructions for the JED8430ADB
61-75 of 77