Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JDS9860AAP > Instructions

JDS9860AAP Jenn-Air Range - Instructions

All installation instructions for JDS9860AAP parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDS9860AAP
31-45 of 276
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The burner igniter would not spark to light the burner.

  • Customer: Margie from San Antonio, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 14 people found this instruction helpful
I had to unscrew 4 screws on the burner unit and then 2 screws on each igniter. slip the olds out and the new ones in and then replace all the screws. And wa la they sparked and I was cooking again.

F1 code and oven wouldn't operate

  • Customer: Robbie from Hillsboro, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 11 of 14 people found this instruction helpful
I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

After self cleaning the oven received an error code telling me the sensor was bad.

  • Customer: Christine from Davie, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

The switch on the exhaust fan for the grill part of the stove went bad. I found the part on your site easily , ordered it and got it within 4 days.

  • Customer: Al from Abbeville, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 22 people found this instruction helpful
I simply looked at the new switch , to see how it fastened in the stove. It had plastic clips that were easily depressed to allow the swithch to be removed. I removed it , (after turning the circuit breaker off to the stove) removed the three wires , and replace them on the new switch and simply pushed it in the space. It snapped in place , and the job was done . Works great!

Oven kept shutting off, getting F-3, F-5 messages on LED readout

  • Customer: ken from north andover, MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 13 people found this instruction helpful
I was out pricing new stoves. Why are slide in stoves twice the price of regular stoves?? I tried one last go at ordering part, overnight mail. Needed to get it fixed for the holiday meal. Part came within one day, early, and it worked. Stove fixed easily, spent the money on a big screen TV.

Burners were leaking gas, igniters didn't work

  • Customer: Mitch from San Jose, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 10 of 14 people found this instruction helpful
I had to use a pipe wrench to remove the burners. They were pretty stubborn to remove from the insert. Once this was done, I installed the ingniters into the underside of the burner, then installed the venturi tubes. After that, installing the burners only took simple placement and a quarter turn to lock them in. I adjusted the burner with a screwdriver and wrench as per the manuals instructions and that is all it took. I did a repair that cost me approx $150.00 to all 4 burners instead of buying two complete new burner inserts for $600.00 and it took less than 1 hour to do. I would do it again anytime.

1998 oven unit flashing F3

  • Customer: chris from houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 14 people found this instruction helpful
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Element Broke

  • Customer: Phyllisa from Plain City, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
Piece of cake! Took more time to find the screwdriver than it did to replace the element!
Unplugged the stove. Removed 2 screws. Pulled the element out about 2" and disconnected the wires on each end (wires are attached to a metal clip that just pushes on to the end of the element. Threw the old element away. Unpacked the new elements. Connected the wires at each end. Pushed element into place and screwed in 2 screws. Plugged oven/stove back in and voila! That's it!

Oven failed to maintain the set temperature.

  • Customer: Thomas from Clarksville, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

oven getting 50 degrees or more, hotter than setting

  • Customer: Joseph from Wappingers Falls, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

replace bake element

  • Customer: Wil from Wichita, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
very very easy. but keep in mind that step one, killing the power at the power box. I jumped that one to a near disastours outcome, thankully all turned out well byt there was a hell of bang and VERY bright flash. Still was worth "doing it yourself" just keep in mine the cut power side...Safety first!!!

inner glass busted

  • Customer: robert from orange, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.

Replaced screws and handle,pulled hinge's out to first stop and slid door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.

PS: shipping was fast and price was great.
Thanks Bob G.

oven would not come up to temp. that was set

  • Customer: David from Green Lane, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 7 people found this instruction helpful
Replacing the sensor kit and door gasket was no problem at all, however the baking element was A different story.
The problem was not the fault of the replacement part, but
the removal of the element to be replaced. The phillips head screws stripped out very easy and getting them out without damage to the interior finish of the oven was time consuming and challenging, but patients, and perservrance
win and so did I. Oven now works great

oven wouldn't heat

  • Customer: James from walnutport, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
removed the screws,pulled the element out about 3 inches disconnected the 2 wires

Oven door locked and was flashing code F4

  • Customer: Mary L. from Trinity, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..
All Instructions for the JDS9860AAP
31-45 of 276