Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JDR8895AAS > Instructions

JDR8895AAS Jenn-Air Range - Instructions

All installation instructions for JDR8895AAS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDR8895AAS
91-105 of 300
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the element was fried in half

  • Customer: Rosemary from Louisville, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
only 2 screws held the element in place pulled the wires and replaced with the identical part very easy to do and thanks for having the part available

Element Wouldn't Heat

  • Customer: Lawrence from Lakeport, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the two screws that hold the element in place, moved it out to expose connecting wires, then removed wires and put in new element.

Broiler element broken, burned and arced about 4in from rear of oven

  • Customer: Noel from Pollock, ID
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
1) Unplugged the electrical cord and removed the oven door (only when easy); and, jockeyed the oven into better working area.
2) Removed about 9 screws holding rear sheetmetal backing plate to disconnect each of 2 electrical wires from the old element.
3) Removed 2 screws holding element to back of oven and 2 screws from small bracket supporting end of element to top of oven.
4) Replacement element was severely damaged. It was at the very bottom of a box 20 by 15 by 15.5 inches high with the large continuous bubble wrap stacked only on top. Each of the wire ends were sharply bent; one almost 180 deg. pointing in the opposite direction, and the other about 120 deg. The element itself was about 4-5 inches out of square. Using two large needlenose pliers I carefully bent each wire back to its proper place. Next I carefully exerted pressure on the element to gradually form it back to as near its correct shape as possible. (Only the inside of the shipping box showed the signs of possible damage.)
5) Installation- The element, from inside the oven, was placed back through the two holes in the rear of the oven and secured with 2 screws.
6) The bracket supporting the front of the element was slid onto the element and attached to the top of the oven.
7) Attached the 2 electrical oven wires to the 2 element wires, making sure there was good clearance to prevent any short circuit, plugged the oven cord in to 230volts, and checked it out with power to the broiler to give myself some confidence that the damaged wires would not quickly break. It seemed to work and I unplugged the oven.
8) Reinstalled the backing plate with the original screws, plugged oven back in, and moved the oven back to its place and replaced its door. It is working and my wife is cooking.

Inside glass shattered during clean cycle

  • Customer: Chris from Lebanon, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.

Very simple project.

Broken Inner Glass Pane

  • Customer: Joseph from Lewiston, ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 7 people found this instruction helpful
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

oven not heating to set temp. 100 degrees too cold

  • Customer: Robert from Funston, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Lower Oven element burn out.

  • Customer: Joseph from Boerne, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Our Maytag electric range has a small oven on top that doubles as a toaster, and food warmer. The lower one is a big oven suitable for Thanksgiving Turkey Etc. It is also a broiler as is the top oven. The top one had the bottom element burn out about 5 months back as well. Now the bottom element on the lower oven had burned out as well. The oven has some age on it, but when I looked to replace it I saw it would be approx $1800.00 - $2000.00 for a new one. I knew the elements were replacable and thought if I should call out the lonely guy, the Maytag repairman. Nope, I pulled the stove out disconnected the 220 power supply. I got the Model number off the back stamped info plate. I looked up Maytags parts on Google and the first one was PartSelect.com. They have easy fill-in spaces for Model and Make and a schematic of the oven and all it's pieces are visually displayed. I found the part I needed and ordered. It arrived in two days, very reasonable, very fast shipping. Pulling out the old elements required only a battery operated screw driver, a flash light, and a magnetic dish to keep track of the screws.The removal of the rear panel takes about 10 sheet metal screws. I marked the leads I disconnected by color with a felt tip pen on the back. I disconnected and removed the aforementioned clips, cleaned inside the oven and placed the new element in, reconnected everything on the back as it had been according to my color assignments, replaced the back with battery operated screwdriver from the magnetic dish, reconnected the 220V power supply. Done, in about 30 minutes; I saved a bunch over a new Stove and at least a couple hundred over a service call. Easy and satisfying.

The heating element was damaged by a fire extinguisher.

  • Customer: Cody from Medford, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
First I unplugged the range from the wall outlet power source...VERY IMPORTANT!!! Then I unscrewed the 2 mounts in the back of the range that hold the heating element in place. I removed the old and installed the new one and reattached the 2 new mounts with the original screws and plugged the range back into the wall outlet. Other than the small and dark work space inside the small oven, it was super easy to do and probably saved us $175!

Lower oven lower electric element

  • Customer: Anthony from Crownsville, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
It's a straightforward remove and replace with two screws. The lower element is most likely to go with years of baking when bake pans overflow on to the element, It can be checked with an electrical probe for resistance and continuity. If the oven is preheating and the lower element doesn't heat that is definitive. We had it checked under the extended warranty but the tech wasn't thorough enough. The extended warranty is of questional value.

After doing an oven self clean cycle, oven temp couldnt be set correctly, heat element was warm,not hot

  • Customer: Philip from Winter Haven, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Oven Over Heating

  • Customer: Steve from New Albany, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

I was washing the top of my stove, and shorted my igniter harness, yow!

  • Customer: Salvatore from Fraser, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable), Wrench set
  • 1 of 2 people found this instruction helpful
When I was cleaning my stove-top, water got down into the igniter switches, and shorted them out. After buying the switch harness from Part select, I had some idea how to install it, but thankfully they had online, step by step instructions. That save me a lot of time and trial and error time. It went in perfectly with their instructions. Thank you very very much for all your help! God Bless!

broken burner knob

  • Customer: James from Cookeville, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
put the new one on. simple and sweet.

Oven not heating to desired temp

  • Customer: Raymond from Ridgecrest, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 5 people found this instruction helpful
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

upper broiler element was shorted, little fire ball at break

  • Customer: Dennis from Chippewa Falls, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
turned off the oven at the main breaker. removed the four screws...two in back and two on the upper holding breacket.
removed the element and disconnected the spade contacts by just pulling them apart. measured it. Compared measurements
with items in catalog. Found exact match, ordered it.
Put it in same as out only reverse.
easy.
All Instructions for the JDR8895AAS
91-105 of 300