Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JDG3000A > Instructions

JDG3000A Jenn-Air Dryer - Instructions

All installation instructions for JDG3000A parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDG3000A
586-600 of 801
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

tub belt broke

  • Customer: chris from lincolnton, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
raised the lid, removed 2 bolts from front face, laid dryer on its back,and replaced belt, very simple. took approx. 20 min.

the dryer belt broke (worn out)

  • Customer: ROBERT from BELMONT, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Opened up the dryer, to discover the broken belt at the bottom, read model, serial number. Went on line, found sites that gave parts lists and diagrams. Wrote down part no. Used Safari to find the part. PartsSelect was cheapest, had it in stock, and could ship fastest. Sears was more expensive and slower. The part arrived in 3 days as promised.Overall, it was excellent service.

belt broke

  • Customer: Terry from Holday, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I have never done this before, so I watched the video and also watched a youtube video for this model to repair belt. Used a gallon paint can to hold up the drum, while I secured the belt. whoooo hooo I did it all by myself...59 yr old Female Do it yourself enthusiast! Thanks for all the information.

Dryer would only go through one heat cycle and then after that the dryer would spin with no heat.

  • Customer: David from Agawam, MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I had no idea how to take my dryer apart so it took me a little while to figure out. I hope by me writing this out my experience might help someone else fix their dryer instead of having to buy a new one. 1)I removed the lint screen assy by removing the 2 screws that hold it to the dryer top. 2) I popped up the front of the top of the dryer which is held to the dryer body by 2 spring type clips. Removed by prying up the top using a big screw driver to release it from the clips.3) Reaching through the top of the dryer and feeling down along the front there is one fastner on each side that holds the dryer front to the dryer body. I removed using a nut driver. 4) The dryer front then can be removed by lifting it up to release it from 2 hooks on the bottom that it hangs on. 5) The coils were located at the lower left side of the dryer as part of the gas heat assy. There is a bracket that holds the 2 coils in place using 2 screws. I removed these 2 screws. Then the old coils can be lifted off the valve post. Then unplug the electrical connector from the old coil and plug in the new coils. 6) Reverse the process to reassemble. After this my problem was fixed and my dryer is working great.

Drier stopped heating up

  • Customer: Daniel from Lake Geneva, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

The door was not catching. The female part to the door closing mechanism broke. It was such an easy fix! Took about 30 secs to fix!!

  • Customer: Gary from Milford, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out the broken part than easily snapped the new part into place..

Dryer Stopped Working

  • Customer: Jerald from Richmond, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
With the help of web sight found the high limit thermostat that was the problem web sight showed how to check it to make sure that was the issue. Then when I ordered the part kit the parts arrive before I expected them to arrive. Was one of the best experiences of ordering on-line we have had thank you ps if we need parts again we will be ordering from here

broken drum belt

  • Customer: Richard from Westmorland, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off power. Opened the top, removed 2 screws one on each side of front door. Opened clip and removed switch and unplugged wire. Removed front door by lifting it up off bottom clips. Removed the drum and checked the drum support wheels, idler and motor pulley. Shop vacuumed everything to get all the lint, dirt and spider webs out. I was lucky, my idler has a spring, so I cut a small piece of wood and put it between the exhaust pipe and the idler to keep it out of the way. I replaced the drum, slipped the belt over the drum and centered it over the pulley (old belt mark on the drum). I reached under the right side and put the belt around the motor pulley and carefully removed the wood holding the idler, turned the drum by hand to check it. Set the front door back in place, plugged the wire back in, put the switch back in the clip, put the 2 screws back in, turned the drum by hand again. OK! Turned power back on and started the dryer. Total new belt installation time was under 10 minutes.

Broken Belt

  • Customer: James from Grafton, VA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
In accordance with supplied video and instructions. Special note - watch out for sharp edges on the dryer panels!

Dryer wouldnt start.

  • Customer: Amanda from Ithaca, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged the dryer, popped the top open, removed the old fuses and installed the new ones. Even removed the front panel & vacuumed out all the built up lint that had caused the fuses to blow. The video available on your site showing how to make the repair was excellent. Showed me everything I needed to know.

belt broke on dryer tub

  • Customer: Guy from Ridgeway, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 2 screws at filter vent on top of dryer Remove screen. Take screwdriver & pry up lid at 2 front corners. Lift lid. 2 more screws inside top front corners.Remove screws. remove front panel.wrap belt around tub. Take cup or can to hold tub in place level.Thread belt around tentioner pulley & motor shaft Look at directions very closely to figure out how to thread belt. read at least 5 times.LOL Reinstall & you are through.PS you can see where old belt rode so try to line up as close to track as possible. Guy

Dryer took multiple cycles to get clothes dry

  • Customer: Michael from Doylestown, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Repair was easy once I figured out how to open the panels (that took some doing since some online videos had me looking for screws rather than just using a puddy knife or flat head screwdriver to release the top cover... no screws). Once opened up, it was easy to find the thermastat and hi-limit parts, as well as the coils. Replacement is simple using phillips head screwdriver.

belt broke

  • Customer: Virgil from Angleton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced belt

dryer wouldn't spin or heat

  • Customer: Robert from Santa Cruz, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I put in the symptoms and was told that 66% of the time it was the high limit thermostat and fuse. I ordered the part and watched the instruction video. The configuration of the dryer was exactly as shown in the video so the installation went very smooth. The dryer has been working perfectly ever since.

dryer belt broke

  • Customer: mark from montrose, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video on the website and saw how easy it was so ordered the part. Part arrived quickly and had dryer up and running within 15 minutes. Good part good price and good intructional video
All Instructions for the JDG3000A
586-600 of 801