JDE3000A Jenn-Air Dryer - Instructions

Very easy repair. Just needed to remove some screws to access the heating element area. The fuses are (1) just above the elements and (2) to the right side of them (if facing from the front). Alittle loosening with a philips screwdriver, removing blown fuses, replace with new fuses, tighten new fuses in place, replace outer screws and job done. Also made sure to fully clean lint collection area. I had a good amount stuck in there and it restricted air flow which caused the fuses to blow. It took 6 years worth of drying to make it happen.

I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

The top was hard to figure out but I found that it pops off at the front with a flat screw driver. Be careful not to scratch the paint. I found that a rear drum roller was bad and the drum seals were deteriorated. I ordered a new belt, roller kit, front, and rear seals. This way I hoped I will not have to take it apart again. The seal were the hardest parts to replace. Make sure you look and remember how they were on before removing them. The directions were not to clear on the seals. The rest were good. It is much better to do it once. Take a picture if possible, it might come in handy as I took mine apart a week or so before the parts came in. I also cleaned out all of the accumulated lint buildup with a shop-vac, including the vent pipe, heater area, and front door. When I was done with this it worked like brand new.

My wife's dryer started squeaking very high pitched, intermittently and then continuously when running. It progressed to a loud shrieking, unbearable throughout the house. Make sure you unplug the dryer. First I replaced the Drum glide and cushion kit. This was easy to do. Pry open the top of the dryer open with a screwdrive or putty knife. Now reach in and remove the retaining screws holding the front panel against the side panels. After releasing the front panel, let it fall forward about 4 inches and then unplug the two wire connected to the door closed sensor. Now carefully slide the thin belt towards the back of the dryer, it will release eventually as it is pulled off the pulley (dont worry, getting it back on is not that hard). Now you can remove the drum. After removing the drum, there are two tan or bluse plastic drum glides that the fron of the drum rests on. They can be worn out along with the cushion beneath them. Replace them with new one. This actually did NOT fix the problem. I put everything back together and....SQUEAK!! Next I undid everything as before and removed the drum. Now I decided to lubricate the rear rollers. First I used a silicone lubricant that again did not fix the problem. I could not find hi-temp lubricant, so I decided to use Axle grease. Bingo...no more squeak. To lubricate the rollers, remove the retaining clip and pull the wheel off. I put an even thin coat on the post they rest on and the inside hole of the wheel. Replace them and remember to put the retaining clip back on. Now replace the belt onto the metal pulley first, with the threaded side of the belt down towards the drive shaft, it should loop around the drive shaft and then you can pull it around the drum, slowly feedingthe drum farther and pulling the belt back along the drom. The smooth side of the belt should be on top of the drum. Now you have to reach back under the drum on the bottom right corner below the lint trap and pull the belt over the tensioner. Sounds harder than it is. Volia...that should fix it. Its been 3 days of non-stop laundry since the repair and no squeak. Next time I will purchase the replacement roller package, but this worked for now. Good luck.

Removed the top cover, unplugged the wires on the element, removed bolt holding the element in place. Replacement took about Fifteen minutes to complete.

After disconnecting power, I popped the lid open by grabbing it on the front sides. Swinging the lid completely back and out of the way, I disconnected the wires from the thermostat. Removing a few screws, the thermostat and the heating element were removed. Reverse the steps and that's it. Very easy repair and now the dryer is like new. While opened, I did take advantage and cleaned all of the lint from the exhaust passages.

unplug dryer---pop the top up---remove 2-1/4 metal screws that attach front to sides---unclip door switch & wires-lift up on front & set it aside--locate blower housing-remove 6-7 1/4 & 5/16 head metal screws--tough part is i had to buy a snap ring plier to get snap ring off motor shaft--use regular pliers,remove spring clip from blo-wheel hub--wiggle & pull blo-wheel from shaft--befoe re-assembling,,vac out all areas inside dryer case-carful not to damage wires & heat element--when clean re-assemble in order removed--also when ordering parts,,my dryer is series 11 (first two digits in serial #)--parts list showed wheel for series 10 & another for series 12---per instructions from a very nice lady on the other end of the parts select phone,always select the lower series--i my case,series 10

unplugged unit, opened lid, removed 2 screws & door switch from front panel, removed front panel & drum.
Removed clips & washers from rear roller shafts, removed 2 screws (each) attaching rear roller shafts to rear of unit. Replaced rear roller shafts, thrust washers, rollers & clips. Removed clip from belt tensioner idler arm, replaced idler pulley wheel & clip.
pulled tensioner toward motor side and locked in place with broomstick. Placed new belt over drum & installed drum/belt into unit, engaging rear drum lip over new rear drum support rollers. Guided belt
over motor shaft and slowly released broomstick to
tension belt. Turned drum by hand to ckeck belt tracking. Reinstalled front panel & door switch, installed 2 screws holding front panel to case. Closed lid. Plugged unit in & tested for proper operation-OK.

This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner sprung to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..

Quick note: I saved over thirty dollars using partselect over the actuall Maytag store parts dept and they still had to order the part to be delivered in 4-5 days. First I pryed the top off of clips in front then removed the screws that hold the element into place, removed the therostat bracket held in by one screw and disconnected wire clips (after labeling the wires) and removed the thermostat from bracket by two screws then disconnected the element wires and slid the old element out. Reversed the process to reinstall the new parts.

First I disconnected the power cord. Next the top of the dryer was easily popped upen with a screw driver by inserting it between the top panel and the front door panel. I removed the two sheet metal screws that held the door panel on the upper right and left sides. The door panel was easily lifted up and out and set it to the side (the door switch can stay connected, the wire is long enough). d I pulled the drum out from off of the rollers that hold the drum in place. No need to remove the belt, it stays in place. I reached through the drum and removed the two hex-head screws that held the roller in place ( I only replaced the left one) and added the new one. I pushed the drum back in place over the rollers (it snaps in place). I propped the drum up with a short screw driver to raise it off of the right and left drum glides (on the bottom). I replaced the felt pads and the plastic glides and set the drum back in place. I also replaced the felt ring (seal) that circles the door opening that the drum also glides on. I glued it in place in spots (with gasket glue). It folds back over itself and forms a double thick pad. You will see what I mean when you see how the old one looks. I replaced the front door panel and snapped the top panel back in place. I let the dryer set over night so the glue would set up. I turned it on the next morning and it is as quiet now as when it was new. Oh ...Jay (the husband) did the work not Jean the wife (her dryer, her credit card)

I unplugged the dryer and then opened the top by releasing the two clips with a large flathead screwdriver. The heat element tested good with ohm meter but the thermistat was open. Replaced the thermistat and it fixed the problem.

Was told by repairman that the to replace the heating element in my Performa dryer would cost approximately $185.00 (not incl.tax). Ridiculous! Order part for $59.00 and received it a day after it was ordered. Went to work installing heating element. Five minutes later I was finished. Thanks.

used a flat blade screw driver to open top up(like a car hood) then removed two screws that held the front panel on. Two more screws held the lint colector part in place. The only problem that I had was that I had to use Elmers white glue to hold the gasket that ran around the lint colector in place.Just a little dab, not enough to soak it.When I took the part out there was about a volleyball's worth of lint in the fan blower. Ordered the part and 2 or three days later I had it. If I need another part I will be back...

First I removed the 2 screws located on front panel securing dust collector in place, then I removed the two screws on the side of the dryer that secure the front panel. I also "popped" the top
of the dryer from the front panel. The front of the panel was then detached from the dryer. I thenpulled the gasket away from the collector, removed the old one and installed the new collector. Part of the kit also contained a new gasket to the exhaust duct, I merely removed the old gasket and installed the new one.. All this was notas hard asit sounds. The diagram from PartsSelect site helped