Models > JDE2000WC > Instructions

JDE2000WC Jenn-Air Dryer - Instructions

All installation instructions for JDE2000WC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDE2000WC
511-525 of 662
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Blower wheel broken

  • Customer: Wesley from Midland TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
UNPLUG DRYER!! Pry the top up with a screw driver. Removed 2 screws holding front panel on. After removing screws, I removed the two wires running to the door switch. The front panel then can be removed. There are many screws around the blower housing that have to be removed to bet to the blower wheel. Use pliers to remove blower wheel clamp. I used a flat screw driver to remove the retaining clip. Pull the old blower wheel off. I then had to use a piece of pipe with a rubber hammer to drive the new wheel on. I then used the pliers to put the clamp on the blower wheel. Then put the retaining clip back on the end of the shaft. I put the blower housing back together with all of the screws. The thermostat is located on the external of the blower housing plate. unplug two wires and unscrew two screws. The reason I had to replace was due to me not unplugging the unit before removing the thermostat. Put in new thermostat with two screws then reattach two wires to correct pins. I took a picture before removing to make sure I had the wires in the correct spots. Assemble the front panel and attached the wires to the door switch. Close lid, plug in dryer, and ready to use.

Tub would not turn

  • Customer: Lynn from Adel GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and performed as instructed- Could not have been easier- Great site with Great information

Broken dryer belt.

  • Customer: anthony from redmond OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I came home from work to notice the dryer singing a different tune than usual. I opened the door and noticed that the tub wasnt turning. I popped the top of the dryer up to find a disentigrated belt. Fired up the computer and in a few minutes had ordered the $8 ($15 including shipping) replacement belt. 3 days later took the shopvac and cleaned up the lint and broken belt pieces. Installed the new belt and was back in business with my 8 year old dryer. ** The only complaint comes from my wife who got her hopes up for a new front load washer and dryer** Thanks PartSelect for saving my wallet in more than one way!

dryer belt replacement

  • Customer: Donald from Horseheads NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video on the site and it was spot-on! Super-easy, took like 10 minutes to replace the belt. Thanks!

Dryer would not turn on

  • Customer: Tim from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
These two parts would keep the dryer from starting but were not my problem. I misdiagnosed this problem. Using a meter to check continuity across the terminals, I checked these two parts and one looked like it had resistance. It did and was suppose too. Not having anything to compare to I ordered both parts. The actual problem was a heat switch that is tucked around the back of the dryer, up against the heating element. It has two white wires running to it. I tested it and it was open. When I joined the wires together, my dryer worked.

BROKEN BELT

  • Customer: James from Grafton VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
In accordance with supplied video and instructions. SPECIAL NOTE - WATCH OUT FOR SHARP EDGES ON THE DRYER PANELS!

Dryer wouldnt start.

  • Customer: Amanda from Ithaca MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged the dryer, popped the top open, removed the old fuses and installed the new ones. Even removed the front panel & vacuumed out all the built up lint that had caused the fuses to blow. The video available on your site showing how to make the repair was excellent. Showed me everything I needed to know.

belt broke on dryer tub

  • Customer: Guy from Ridgeway VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 2 screws at filter vent on top of dryer Remove screen. Take screwdriver & pry up lid at 2 front corners. Lift lid. 2 more screws inside top front corners.Remove screws. remove front panel.wrap belt around tub. Take cup or can to hold tub in place level.Thread belt around tentioner pulley & motor shaft Look at directions very closely to figure out how to thread belt. read at least 5 times.LOL Reinstall & you are through.PS you can see where old belt rode so try to line up as close to track as possible. Guy

belt broke

  • Customer: Virgil from Angleton TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced belt

dryer wouldn't spin or heat

  • Customer: Robert from Santa Cruz CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I put in the symptoms and was told that 66% of the time it was the high limit thermostat and fuse. I ordered the part and watched the instruction video. The configuration of the dryer was exactly as shown in the video so the installation went very smooth. The dryer has been working perfectly ever since.

dryer belt broke

  • Customer: mark from montrose IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video on the website and saw how easy it was so ordered the part. Part arrived quickly and had dryer up and running within 15 minutes. Good part good price and good intructional video

Dryer Belt Broke

  • Customer: Reid from Cumming GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Fortunately this is an easy diagnosis and easy repair. The great PartSelect instructional videos are a HUGE HELP!!

My dryer would not start

  • Customer: joby from morrisville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went on this site and started to search for possible parts that I thought I could change out that would make my dryer run after having changed out my time that wasn't broken (lol). I stubbled across the section that had troubleshooting tips on it . Wow I couldn't believe my dryer was on there!!! So I looked at the number 1 problem most people had with this model dryer and it was the high limit kit. So I figured for $22.00 what would it hurt so I ordered it and it got to me in 2-3 days and it was soooooooooo easy to change . I couldn't believe I was thinking of buying a new dryer . My old dryer has been drying clothes ever since and no problems . I owe it all to this site . Thanks guys at partselect and everyone else out there that took the time and left comments . It saved me $500.00 that I didn't have to spend after the holidays . You guys are awesome!!!!!!!!!!!

Broken belt

  • Customer: Rick from Emporium PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the instructions that came with belt everthing went just fine.

couildn't see the belt tensioner and hold it back at the same time

  • Customer: Matt from Norristown PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I drilled two holers in the side of the cabinet 1 inch apart. I put them at the same height as the tensioner spring. I put the string through 1 hole and around the tensioner. I pulled the string through the other hole and had my son hold the tensioner back while I reached in and lined up the belt on the tensioner while my son let out the string slowly.
All Instructions for the JDE2000WC
511-525 of 662