Models > JDE2000A > Instructions

JDE2000A Jenn-Air Dryer - Instructions

All installation instructions for JDE2000A parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDE2000A
451-465 of 596
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

blower not rotating, hub worn

  • Customer: Kenneth from ELYRIA AL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unfortunately, the part that came in was a major problem. The shaft hole was way undersized and probably made for a much smaller shaft then the one on this dryer. I had to bore out the shaft and drill and tap a set screw to lock the blower to the motor shaft. I would estimate that the opening was at least 1/8" smaller than the shaft and as it was molded, the flat for locking the blower had to be drilled out as well. Even so, as I pressed the unit onto the shaft, it split and I had to do major work to make the blower usable. Until now I have been very pleased with the quality of parts from Partselect however this critical part did not meet the manufacturer's specifications as to the bore for the shaft.

broken belt

  • Customer: Mark from Ridgway PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the belt

blower wheel wore out

  • Customer: Nancy L. from Wardensville WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
ordered a new fan from your web site and replaced it. it only took a couple of days to get the part thanks for such good service well pleased will use you again in the future

broken belt

  • Customer: john from estill springs TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
even though the motor pully was invisible to me, i was able to, by feel, thanks to your diagram, install the belt.

Torn dryer drum belt.

  • Customer: Donald from Allentown PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed front dryer panel removed torn belt and replaced it with the new belt.The job was easier than i thought.

dryer would not start

  • Customer: Steve from Winter Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
watched available video on site removed 4 screws all at top of washer. had to replace heater element, thermostat and thermal fuse. very easy.

The blower fan in the dryer broke into pieces and was flying out threw the dryer vent

  • Customer: Delores from Palmerton PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Removed the front of the dryer removed the casing from the front of the blower and put the new fan in. And now it works great Thank you

dryer belt broke

  • Customer: mary from wimberley TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
ordered the part late sun. afternoon. arrives ups on tues.am. took dryer apart and replaced belt and up and running in about hour and half. works great. dyrer is about 25 yrs. old.

The drum quit turning

  • Customer: Paul from Bryan TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Sunday, the drum on the dryer quit turning. I could hear the motor running, so I guessed that the belt had broken. I jumped on the internet and searched for Roper Dryer parts and Part Select jumped up. Within 30 minutes, I had a new belt ordered. I received the e-mail with the how-to included and boy did it save me some hassel. I was prepared to do it all wrong until I saw the video. When the belt arrived, it took me longer to gather the tools I needed than it did to change the belt. Thanks

no visual access to the area we trying to work in.

  • Customer: Preston from Ventura CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
To start off I am disabled so I had my 14 year old daughter to help me.I opened the top of the dryer,disconnected the door button and had my daughter help wire the top open and take off the front panel.We took this time to clean out the dryer for it was quite built up with lint.I then gave my daughter my cell phone and told her to stick it in the dryer to take pictures of the area we needed to work on.I then showed her the pictures and explained in detail how everything worked and what she needed to do.I then put the belt around the drum and she proceeded to put the belt on the pulley and tension rod.At this point we are both filty and both have gotten miner injuries.I spun the drum and it and the belt both spun,we thought GREAT we have fixed it,so we put it all back together,plugged it in and nothing.So we take it back apart,but this time I stick my hand in there and find out she didn't have the belt on the pulley,it was wrapped around the tension rod so I fixed that problem.Then I figured out that she hadn't pulled the tension rod over to its proper place so I do that as well.This time I spin the motor fan in front to make sure we have it right.We put it all back together, plug it in and it WORKS,so we throw the jeans in because we have to be at a B DAY party in a couple hours.The dryer buzzer goes off and we both go to check and the clothes are soaking wet.I open the top of the dryer and the brand new belt is broken.So many mixed emotions at this time I cant tell you how disappointed and upset we where.So she took her jeans out and used a hair blow dryer to dry them and I hung the rest all over the house.So I decide not mess with the dryer for a couple days because of my frustrations with it.We have to do laundry everyday,I have three teenagers,so I have clothes drying all over my house every day.Even went to the laundry mat once $40.00 it cost me.A couple days go by and I decide to see what happend. This time I have my 15 year old daughter help me.I completely disconnect the dryer from everything.We put it on top of A table and take it apart.What do I find?the motor pulley is broken and has jagged edges the shredded a piece of the new belt.As I mentioned earlier I am disabled and am on SS so I only get paid once a month and have no extra money so now I have to wait until the end of November to order another belt and the motor pulley.In the mean time there is wet laundry hanging all over my house with fans blowing on it to help dry it faster.So what was supposed to cost approximately $20.00 to fix is now going to total over $100.00.I do thank you for the speedy delivery of the dryer belt and we had A great time at the B DAY party.thanks

Dryer drum would not turn

  • Customer: Peter from Evanston IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I researched the issue, found a video and ordered the belt, which came in 2 days. It was inexpensive, and I had my dryer back and running in less than 3 days. I did get my son to help me as it might not be that easy with just 1 person (to hold the drum in place while putting the front back on). Great service and great information on how to do the repair.

Belt Broke

  • Customer: Dawn from West Sand Lake NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
When we ordered the part we watched the video, to see what needed to be done and both my husband and I got the dryer all ready for install before part came so when the Ups delivery came it took all of 10 min to get it back up and running! Thank you so much for having the details and a video made thing go so well! Sincerely Dawn

broken belt

  • Customer: Mandi from El Dorado AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I loved the demo video on how to do the repair-it was very helpful. My dryer was different than the one on the video, and I had to make adjustments ( I had self tightening screws on the top and bottom of the front panel and then I stripped the screws)I did this by myself and I had to prop up the drum AND the front panel with items in laundry room.) That's why it took me longer than demo (also had to run to hardware store to get screws). Felt great to accomplish this by myself. Thanks!

broken belt

  • Customer: wallace from meriden NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I know now that I did not have to get in the back of the machine. Only lift top remove two screws for the front and lift off.The most diffcult was determing how the idler and belt went in but if you hold it in position it becomes to you. Thanks for all your help you run a good ship.

Broken belt

  • Customer: Tracy from Bakersfield CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I unplugged the dryer then loosened the screws on the top and inside front, took the front off, I didn't need to unplugged the socket wiring attached to the door. Removed the drum (it came right off) wrapped the new belt around the drum, fed the belt through the tension flange and looped it over the pulley. Then rotated the drum a few times by hand to line everything up then put everything back together. It works fine now.
All Instructions for the JDE2000A
451-465 of 596