JDE2000A Jenn-Air Dryer - Instructions

i first watched a video on U-Tube and did exactly as they did. removed screws from the lint tray, pried up the top panel of the dryer with my putty knife, unscrewed the 2 hex screws at the top, disconnected the plug for the dryer door,and installed the new belt it really was pretty easy. the only thing I would recomend would be when installing the belt put towel or anything that would protect your arm from the botttom piece of sheet metal. I got a pretty good cut on my forearm while I was putting the belt on the bottom pully.

You have taken me as your life-time customer. Product was so east to install. I love it how you have short videos that take you step by step. By far, that was the best thing. Thank you so much!!!!!!!!!

raised the lid, removed 2 bolts from front face, laid dryer on its back,and replaced belt, very simple. took approx. 20 min.

Opened up the dryer, to discover the broken belt at the bottom, read model, serial number. Went on line, found sites that gave parts lists and diagrams. Wrote down part no. Used Safari to find the part. PartsSelect was cheapest, had it in stock, and could ship fastest. Sears was more expensive and slower. The part arrived in 3 days as promised.Overall, it was excellent service.

I have never done this before, so I watched the video and also watched a youtube video for this model to repair belt. Used a gallon paint can to hold up the drum, while I secured the belt. whoooo hooo I did it all by myself...59 yr old Female Do it yourself enthusiast! Thanks for all the information.

1st replaced the broken drum belt, then the heating element failed, ordered a replacement, arrived over night thank you very much. Installed new heating element, 5 minutes later the motor failed. Bought a new dryer, ate the heater element as it is now used.

With the help of web sight found the high limit thermostat that was the problem web sight showed how to check it to make sure that was the issue. Then when I ordered the part kit the parts arrive before I expected them to arrive. Was one of the best experiences of ordering on-line we have had thank you ps if we need parts again we will be ordering from here

Shut off power. Opened the top, removed 2 screws one on each side of front door. Opened clip and removed switch and unplugged wire. Removed front door by lifting it up off bottom clips. Removed the drum and checked the drum support wheels, idler and motor pulley. Shop vacuumed everything to get all the lint, dirt and spider webs out. I was lucky, my idler has a spring, so I cut a small piece of wood and put it between the exhaust pipe and the idler to keep it out of the way. I replaced the drum, slipped the belt over the drum and centered it over the pulley (old belt mark on the drum). I reached under the right side and put the belt around the motor pulley and carefully removed the wood holding the idler, turned the drum by hand to check it. Set the front door back in place, plugged the wire back in, put the switch back in the clip, put the 2 screws back in, turned the drum by hand again. OK! Turned power back on and started the dryer. Total new belt installation time was under 10 minutes.

I watched the video on the computer and it was very easy to repair I had the dyer apart ,fixed and put together in about half hour

We watched the video on the PARTS SELECT site and it was very helpful and I had no problem holding the flashlight for my husband!

Had a hard time at first trying to figure out how to place the pulley wheel that you place the belt around, it holds it in place so to speak, was getting very frustrated came upstairs went on line to your web site and lo & behold there was a video on how to do it, I watched that video (thanks Steve) and went back down cellar and had the belt on in less than 5 mins and everything is working fine. Thanks for all your help Dan

After some online research on parts select I purchased a high limit kit. Lifted up top of dryer. Took out heating element then replaced thermostat and fuse. Reinstalled heating element, closed top, pluged it in and I had power. Saved me about 400-500 dollars. I wonder how many people go and by a new dryer and all they need is a $26.00 kit???

The repair on replacing the clothes dryer belt went great. Not only did Part Select send me the correct belt at a great price .. the helpful hints that other people gave was most helpful. The only glitch was when I was pushing the tensioner wheel to get the belt around the pulley it slipped and the spring came off. The instructions/tip of taking the drum out and how to replace it came in handy when I had to get the spring back into place. The belt finally went on but there was a slight twist in it by the tensioner wheel. Again the tip I got with my e-mail helped as I manually turned the drum and was able to right the belt. Kudos to the tips I received and the confidence I could do the job myself!!!!

open top lid by inserting putty knife in seam above dryer door apx 2-3 inches from each side push in against the clip and pull top up off of clip. follow same for other side. remove screw from inside cabinet apx 2' down each conner disconnected door switch by pulling crimp from spade on switch. lift front off. lift drum out. remove switch bracket holding the thermostat switch. remove screw from heater box that is on the right top side holding limit switch brackrt in place. lift bracket and switch replace switch and re-install. replace thermostat and re-install. place belt on drum rib side down on drum surface. pick drum up by belt ane place back inside cabinet. make sure to snap drum back into rollers. reach in from bottom front left side of dryer push tension roller to the left with other hand reach in on bottom front right side and place belt over roller and release roller gently turn drum by hand and make sure belt is tight and drum spins with belt. replace front re-attach wires and screws lower top and snap in place. plug unit in and good to go

push in on clips on front top at seams apx 2-3 inches from both sides. lift lid lean it back. remove door switch. remove front panel. remove old belt. replace with new belt lifting drum slightly to get around drum rib side down. reach in and push tensioner down to the left place belt around pully and over tensioner relase gently put all item back together.