JDE2000A Jenn-Air Dryer - Instructions

Thousand dollars for a new dryer or twenty bucks for a new belt. Thank-you parts select. Ordering was easy and the instructions were bang on!

The video for the Heat Kit replacement is excellent. However, i could not replace the fuse without removing the heating coil. It was the only way my hands could get the fuse bracket out/then in. I accidently inverted the heating coil when trying to replace it, and struggled for a minute or so. Be sure your HC coil is in the same position as when you removed it. You might want to include the heating coil removal as a standard part of the replacement video. He specifically mentioned NOT having to remove the coil. Otherwise the video and and the instructions are perfect. You need to make sure you clean out the tubing/vent prior to replacing the thermostat and fuse. Otherwise you are wasting you time. Perfect repair, easily done..luv it.

follow video and fix.

I lifted the top of the dryer. I unhooked the hangers from the door and took it off. I pulled the drum out, took the broken belt off, slid the new one around the outside middle of the drum, turning the rib side of the belt out,and ran the belt through the pulley attached to the bottom base of the dryer (tension pulley, right hand side), slid the drum back inside the dryer frame, reattached the door, closed and snapped the dryer lid and it worked great!!

Your customer service was great, but your video wasn't particularly helpful because of the extreme age of my dryer. For one thing, with these really old dryers, you don't have to slide the drum out at all; you just unscrew the front panel and slip the belt in that way. The printed diagram that came with the belt helped me figure how the belt slips through the pulley assembly, but the drawing could have been more clear. In spite of my bickering, I probably saved $50 fixing it myself.

Disconnect electric power, the top & cabinet are connected by 2 reusable locks about 4 inches from each front corner, use a thin flat putty knife or similar object, push inward on a lock while lifting gently on the front of the top piece, then let the top rest against the wall. ( a wire on each end of a safety switch for the dryer door may need disconnected) Remove a screw from each front corner of the cabinet, then pull upward on the loose front panel to access the drive motor, remove old belt. install new belt by lifting the front of the drum just high enough to allow the new belt, place groves of belt against the drum and around the motor pulley and belt tensioner, re-install cabinet front, (re-connect safety switch wires) return top and push down at cabinet locks.

It was really easy I watched your video on how to do it the video went step by step and was very helpful

I watched a part select youtube video on possible fixes for the problem I was having. Ten minutes and two videos later I had the part out and identified as the problem. I ordered the part ($42.00) which arrived four days later. Spent ten minutes replacing it in machine, turned dryer on and went right back to performing the way it has for the last 12 years. Easiest thing I did all day. Saved me $400 bucks too. Thank you.

Watch the video you sent me, and every thing fell into place

Took less than five minutes to fix a couple screws and take some wires off and pull it right out. Called local apliance store if they had part wanted more than partselect with next day shipping

What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

Raised upper portion of dryer using putty knife on clips just above dryer door. removed 2 screws on inside corner above dryer door, then completely removed the front panel. Lifter out dryer barrel to expose the inner workings. Removed the 2 rollers at back of unit...(be sure to apply some med. weight grease on roller shafts... I used axle grease). Also, had to replace the blower wheel, original was broken in half. With 1/4" nut driver(if I remember correctly) remove the 6-7 screws holding the front cover on the fan blower assy. Using pliers remove the spring clip on front of blower wheel shaft. Upon installing new blower fan you might have to align the new wheel on shaft with the flat keyway then using a 1/2" socket hold it on the front of the blower wheel and lightly tap the wheel in place till seated at the back of the shaft. I use to assume that the majority of the noise I was hearing was coming from the busted dryer. I did have underlying suspicions that there was another source of noise from within my domicile. Once the dryer was re-assembled and 'purring' just like new my suspicions were confirmed. I was able to verify that the source of the 'other' noise was from my wife. I miss my old dryer!

I opened the lid and using the Nut driver removed the old High limit Thermostat.Then repalces the new one, replaced the lid and plugged in the dryer.It still did not start.I then found the fuse hiddden on the side of the heater element, testd the fuse on it was blown. I placed an order for the fuse.

I basically followed the instructions in the video provided. They were very clear and detailed. I love this website. This is the second repair on this dryer using PartSelect.com Runs like new and I saved a lot on labor costs.