JDE2000A Jenn-Air Dryer - Instructions

I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

Found the heating element under top of dryer towards the back and replaced it

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

I unclipped the top of the dryer for access to the heating coils. I unscrewed the bracket holding the high limit thermostat (the heating element was directly below the high limit thermostat). I removed one screw holding the heating element in place, and then removed the faulty heating element. I checked the old heating element and the old high limit thermostat with a multimeter to confirm that they were faulty - both the heating coil and the HL thermostat had continuity but the coils looked like they needed to be replaced (not rusty, but dingy). I installed the new heating element and the new HL thermostat, closed the top of the dryer and ran the dryer - it worked :) Thanks partselect.com!

I went with the majority and started with replacing the thermostat and thermal fuse. It fixed the problem, and all for about $30. The repair was easy, although you do have to do some finger gymnastics to get at the thermal fuse. Of course, I wanted to know why the fuse blew in the first place. I had cleaned the interior of the dryer out last year and I wasn't seeing much of a build up. I then removed all 20 feet of the dryer vent hose and cleaned it out with a kit (LintEatr, about $30)that attaches to your cordless drill. I pulled out a shopping bag full of lint. My clothes used to take up to 3 cycles to dry and now it is back to 1. Clean out your vent hose, people! P.S. There must be a reason for it, but it would be much easier if the fuse had a reset like other heating units do, instead of having to open the dryer up and replace parts.

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

took the top and front off the dryer and had to route the new belt around the drum and through the pulleys, it was really easy and a heck of a lot cheaper then buying a new dryer

Called PartSelect, gave them the make and model number of the dryer and told them I needed a new belt for it. They gave me a price including shipment (under $20.00). I oreder the new belt and it arrived within a week. I also got an e-mail from PartSelect with a video showing how to replace the belt. This was very helpful. I was able to watch the video, take the dryer apart, replace the belt (after a few tries), and put the dryer back together. Problem solved! Thanks PartSelect.

Unplug the dryer. Take a large flat head screwdriver and pop the hood loose from the retaining brackets on the front of the dryer and raise.Next, unhook the wiring from the thermostat and heating element with needle nosed pliers located in the back left corner. Use a 5mm socket to remove the thermostat bracket and the heating element bracket.Remove faulty part and replace. Replace heating element and tighten.Replace thermostat on the retaining bracket and tighten. Plug your wires back in and close the hood.Plug Dryer back in.

Found an instructional, easy to follow video by PartSelect online. It was helpful to know what tools I needed before beginning the job. I first purchased only the belt. After taking the dryer apart, I saw the idler had also broke. It was very helpful that the parts arrived quickly. The video was the the greatest tool for doing this repair myself!!!!

Tools and materials:

#2 Philips head screw driver
Standard flat-tip screw driver
1/4" nut driver or ratchet
1/4" drive sockets: 1/4, 5/16
Something 3-4 inches thick to wedge under drum for support (i.e. scrap 4x4, soap bottle, books)

Replacement Procedures:

1. Unplug dryer from wall outlet
2. Pull out lint screen
3. Remove 2 Philips screws attaching lint trap to dryer top
4. Lift hinged dryer top panel near front and lean it back on wall. You may need to pry between side panels and top with flat-tip screw driver to get it started.
5. Disconnect plug from dryer door switch near front
6. Remove two 1/4" and two 5/16" hex screws inside front panel near top.
7. Open dryer door and lift front panel straight up to disengage tabs from slots near bottom of front panel.
8. While supporting drum with one hand, lift front panel and set aside with other hand.
9. Slip replacement belt around drum with ribs facing drum and position it where old belt left its mark.
10. Wedge something under drum to support it while installing the belt.
11. Re-position tensioner in two slots in bottom panel just in front of motor. On my model the bend in the spring will be on the right side with the idler pulley to the left, when viewed from the front.
12. Ensuring the belt isn't twisted, thread a small loop of it through the opening in the tensioner just below the pulley.
13. With the left hand, push against the tensioner spring while working the loop over the drive pulley.
14. While supporting drum with one hand, remove whatever you put under the drum to support it.
15. Replace front panel by aligning the slots with the tabs near the bottom and lowering it into place.
16. Carefully slip the drum opening over the flange on the front panel and replace hex screws.
17. Slowly roll the drum in one direction or the other until the belt aligns and centers itself.
18. Re-connect the plug for the dryer door switch.
19. Lower the dryer top and press until it snaps back into place.
20. Replace philips screws to secure lint trap and replace lint screen.
21. Plug dryer back into wall outlet, close door, set to dry, and press start.

Removed frontage of dryer removed plate covering bthe blower wheel. Removed clip holding the old blower wheel and inserted new one and replace clip, plate and front of dryer.

just like the training video showed, and was very happy at how it came fast, installed easy and back in the drying business.

Replaced part according to instructions

I watched the video and did the repair myself. My husband, who works in maintenance, was IMPRESSED! Yay! Thank You!!!! Love you guys! I am forwarding your website to my children!