Models > JDB9910AWB > Instructions

JDB9910AWB Jenn-Air Dishwasher - Instructions

All installation instructions for JDB9910AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB9910AWB
586-600 of 605
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Plastic linkage had broken

  • Customer: Sandy from Grass Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Followed the outstanding video instructions. Your company is fantastic. Your attention to detail, the quick shipment (one day) and video ... stellar! We will be referring your company to all!!! Thank you!!!!

I needed a replacement silverware basket

  • Customer: Jillene from Green Bay WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the old one out of the dishwasher and put the new one in. The new one is much nicer and heavier than the original one!

Age made the clips brittle and they broke

  • Customer: Douglas King from Evansville IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snapped in the new ones in a skinny minute. Just make sure you leave the old ones in the dishwasher rack until the new ones come in it can be confusing if they are removed. My wife took them out so I had to figure out how they went back in but was not a big issue. I did have to swap ends to make it right but less than fifteen minutes and like new again.

lime up

  • Customer: myron from Indianapolis IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took inside front off disconnect wires pull old unit out and put new unit in then put inside front back on tighten screws was done unit works like a new machine

spray arm fell off

  • Customer: Mr. Perry from Overland Park KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched the video ordered the part. It was delivered the following morning. Un screwed the spray arm holder put the spray arm and retainer in the holder then screwed the holder back in the dishwasher.

Leak

  • Customer: J Roy from Oak Park IL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I think anytime the motor needs to come out of an older dishwasher, it would be wise to replace the main gasket that goes around the motor at the same time.

Broken Latch Handle

  • Customer: Don from Douglasville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Open the dishwasher door. Remove the inside door cover screws (retain screws). Lift the inside door cover block it open. Remove two screws from the broken handle (retain screws) install new handle install and tighten two screws. Lower the inside door cover install screws and tighten screws. Have a cold beverage (beer).

The lower dish rack has only six wheels three on a side the original had eight wheels four on a side. This new rack does not stay on track.Is there any way to add two more wheels .If not how can I return for the correct rack?

  • Customer: Theodore from East Greenwich RI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Need correct lower rack

plastic piece that holds spring broke

  • Customer: Len from Woodland Park NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Because mine is a portable dishwasher, I had to remove top first. the sides and back are one complete unit. the torque screws are in the front, 2 on top, and 2 in rear. Then the panels can slide back to access the spring. Replace the plastic piece & hooked on the spring. Reassemble in reverse order.

silverwear basket was cracked/

  • Customer: Marylou from Dana Point CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just dropped it in and that was it.

Old basket worn, silverware falling through holes

  • Customer: Thomas from Washington PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took old basket out, put new basket in

Old silverware basket "collapsed"

  • Customer: Lawrence from Newport ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out old, put in new; threw away old. :-)

dishwasher making scraping noise when running

  • Customer: Doug from Columbia City IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Took the dishwasher apart, then went the website and found an extra part. The discharge pump housing had broken into two parts. Order the patrs needed, they came in two days and put the dishwasher back together. It was easy with the help of the website and runs like almost new

Not cleaning bottom rack as wheels broke off

  • Customer: Paul from Cave Creek AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snapped on 5 new wheels in under 5 minutes and this raised lower shelf to keep from hitting circulating water spigots beneath the shelf. Cleans like it was new again!

Dishracks were worn, pieces broke off

  • Customer: Richard from Lyndhurst NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced both upper and lower Dishracks, the Parts Select video shows how to replace the top rack but doesn't mention the lower one. Had a bit of a problem trying to figure out how to remove the spout on the bottom rack. Finally figured out, twist it counter clockwise to remove it and turn it clockwise to reinstall it onto the new lower rack.
All Instructions for the JDB9910AWB
586-600 of 605