Models > JDB9910AWB > Instructions

JDB9910AWB Jenn-Air Dishwasher - Instructions

All installation instructions for JDB9910AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB9910AWB
46-60 of 610
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Not getting clean dishes; filter kept getting cloged.

  • Customer: Joe from Titusville NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
After removing parts, cleaned both upper and lower spray arms, blew out lead to the upper arm, and started to install the new parts.

Unfortunately, the Pump Housing Filter was still cold (freezing weather during shipment and left at the front door) and when I started to bend it into shape it broke in two places. So I tolk the old filter and some Lime away and slowly cleaned it with soft brush to open 95% of the holes.
Once ready it was installed along with the other new parts and the dishwasher works very well.

Simple homeowner repair.

Rusted racks

  • Customer: Paul from Anaheim CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
Most difficult was figuring out how to release the top rack...just flip the end pieces to the side and out they come. Next was removing and reinserting the spray head in the bottom rack...just twist and take out then align and twist into place in the new rack.

dishes still dirty, soap remained in dispenser.

  • Customer: Hans from Show Low AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 12 people found this instruction helpful
After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.

Dishwasher door was crashing open

  • Customer: Bill from Morganville NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 7 of 7 people found this instruction helpful
The replacement of the spring linkage was simple - the pulling out and pushing in of the under-the-counter dishwasher was the difficult and time-consuming part. The repair of the part took less than a minute.

The actual repair -
1. Hook the linkage to the dishwasher door
2. Hook the spring to the dishwasher base
3. Hook the spring to the linkage.

Getting the dishwasher out to be able to make the repair involved:
1. Unscrewing the base panel (6 screws had to be removed)
2. Unscrewing the dishwasher from the counter (two screws)
3. Turning off the water supply
4. Disconnecting the inline water supply from the dishwasher.

Once the part was replaced, I had to return the dishwasher to its original position, which meant performing the four steps (in reverse) used to pull out the dishwasher.

Broken door spring linage and lost spring

  • Customer: David from Mesa AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 8 people found this instruction helpful
Took off bottom plate for access. Slid part that holds bottom of spring forward so I could reach it without pulling dishwasher out of position. Hooked spring to bottom attachment, then connected door spring linkage to holder that is attached to the dishwasher frame. Adjusted the tension with the tension screw and buttoned up bottom plate.

lower rack assembly rusting, needing replacement

  • Customer: Carol from Florissant MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
Old rack assembly was rolled out , the plastic water disperser was twisted off of the old rack and placed on the new rack assembly. The new rack was rolled into place. Project complete.

the soap dispenser wouldn't open during cycle

  • Customer: paul from spring hill TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 7 of 8 people found this instruction helpful
I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

Dishwasher made a grinding sound - very loud. Did a poor job cleaning.

  • Customer: Brian from Elkridge MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 8 people found this instruction helpful
I took the lower pump assembly apart to find the problem. The biggest challenge was figuring out how to remove the cover. In the center, the assembly is held together with a round plastic nut about 1.5 inches in diameter - simply rotate it counter-clockwise to remove. I then removed the pump housing and found the impeller broken in two and the disk that was supposed to be attached to the top of the pump housing broken off. This was causing the noise and greatly reduced efficiency of the pump. I replaced the impeller and upper pump housing (bought the gasket too since it is hard to remove the old one) and put everything back together using the diagrams provided on the site. While many rate this repair as "easy" - it is only after you figure everything out! If you knew exactly what you were doing, the project could be done in 10 minutes. I had to study the diagram and it took me some time to disassemble, figure out what was wrong, read posts, order parts and reassemble. I also replaced the handle which had broken on one side which was simple. Part select is outstanding - I've used this site for my fridge, oven and now dishwasher and have avoided expensive service calls. If you are technically inclined and patient, you can repair your own appliances.

Plastic handle had split (age and wear & tear)

  • Customer: Edward from Ewing NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 6 of 6 people found this instruction helpful
As the screws took a special (non philips) head, I did need to buy a special one in the appropriate size (cell phone photos help!). Then I took off the 8 or so screws inside the front door, removed the two screws for the handle, replaced with new handle and screwed the front door back together. Not hard, would have been faster without the hardware store trip.

Dishwasher leaking water

  • Customer: Marvin from Republic MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 8 of 12 people found this instruction helpful
Pulled the dishwasher out. Determined that it was leaking from the air/water inlet. Ordered the seal and replaced the seal by turning the inside cover counter clockwise while holding the outer water inlet. Replaced seal and installed water hose. Put dishwasher back inside cabinet and leveled. If you don't try to fix it yourself, It could cost more then what it is worth.

I accientally busted the old rinse arm, while I was trying to put in the filterguard with bottom spray arm jet

  • Customer: mary from sturgis MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 6 of 6 people found this instruction helpful
I took the bottom rack out of the dishwasher. I then took the filter guard and bottom spray arm out. Then I took the screws out of the filter guard to get to the rinse arm. I took the filter guard off, took the old rinse arm out and put in the new one. Have to make sure it is completely resting inside there. Then I put the filter guard back on. Put the screws back into the filter guard, put the two arm seals down around the rinse arm, put the bottom arm spray with guard back into the notches, put the screw top on so it can screw back in and the dishwasher is ready to go. Just make sure that you don't have a lot of soap built up, it will not clean the dishes right nor will the spray arms move. I had to call my appliance person out, and I have so much built up from soap, that I had to order a new filter guard and top and bottom spray jets. I now know to switch back to powder or liquid soap, because the tablets make a huge built up of soap... I have these parts on order now. In the meantime, I am cleaning out the jets with dishwasher magic and vinegar while I am waiting for my new parts. I now know how to put things back together so when I have this happen again I will know how to do it to save me the 63.00 office call and parts. I am happy that I know where to get my parts when I need them or break them by accident on trying to put my dishwasher back together again. Thanks.

Tub was mysteriously slowly filling with water.

  • Customer: Mark from Austin TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 6 of 6 people found this instruction helpful
Figured out that the only thing that could be causing this was a bad inlet valve. Repair was really easy. Didn't even have to pull machine out from under cabinet. First removed kick plate. Then placed towel under the old valve. Undid the power connections and water lines (in and out). removed the to screws holding the valve to the body of the washer. With the valve free, removed the brass elbow and installed it on the new valve. Reinstalled the valve and all connections. Works like a charm.

My racks were rusting, and a few tines had fallen off

  • Customer: Stacey from Robbinsdale MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
First I did the top - getting the ends off the track is simple, flip the ends "open" like a book on each side, and remove the caps. Pull out the rack, replace with the new one and replace the caps. Bottom rack was easier once I figured out how to remove the spray tower. Grab it firmly and twist. Place it in the new rack, and roll it into the DW. I'm a fairly handy woman, and this was quite easy.

Lots of noise and wouldn't pump

  • Customer: Joe from Franklin NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 6 of 6 people found this instruction helpful
I first removed the washer arm. Be careful because it is screwed on with the large center plastic piece with right hand thread. That allowed me to take the arm and disc off.

Next I took 6 screws loose with the allen wrench. This allowed me to get to the filter ring. I removed it and that allowed me to get to the three screws holding the discharge. I used a 5/16th socket to remove them.

A plastic disc that was part of the upper pump came loose and caused the noise. I replaced the upper discharge housing (with upper pump as part of it) and upper discharge housing gasket and reversed the order to reassemble.

The exploded diagram was a terrific help

Closer tab on the door broken.

  • Customer: Paul from Austin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if I need to change it in the future.
All Instructions for the JDB9910AWB
46-60 of 610