Models > JDB8910AWS > Instructions

JDB8910AWS Jenn-Air Dishwasher - Instructions

All installation instructions for JDB8910AWS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB8910AWS
76-90 of 596
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wanted to chnage dishwasher panel to match stainless appliances

  • Customer: Debra from Williston Park NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
Open the door all the way. Remove the 7 screws along the perimeter with a Torx screwdriver. Then close the door. Remove the two screws at the bottom of the side of the outside of door panel with a phillips. With the palms of your hand flat on the panel slide the panel up about 1/2 inch and it falls toward you. Follow these steps in the opposite direction to install the new door. I did however replace the two phillips screws last.

The dishrack guide rali stop had come off one of the guide rails, so the wheel in the guide rail would often roll right past the end of the rail, causing the rack to pitch down. this was rather frightening with the rack full of glasses and other breakables.

  • Customer: Margaret from New Ipswich NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
At first I snapped the plastic piece together and then tried to put it in the guide rail. That's where the sharp knife came in handy, to pry the piece apart again and start over. It was easy to see how the piece was supposed to go into the end of the rail and snap in place; I just didn't look carefully before I had to backtrack! I haven't yet tried to put in the other pieces we ordered.

NO WATER INTO THE DISHWASHER

  • Customer: RICHARD from RAMSEY NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 3 of 3 people found this instruction helpful
turned off water at valve, removed float switch, removed water inlet vlv. replaced and reassembled. still not water going into the machine. i have no voltage to the valve or float switch. i then took the door apart to find there were burnt wires as well as a burn mark on the control panel. upon closer inspection, it looks like the door seal has failed and water got into the door. had to replace dishwasher with a new one.

Washer made grinding noise at end of drain cycle

  • Customer: Peter from Long Beach CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 3 people found this instruction helpful
Initially I suspected something had found its way to the impeller or the macerator, began to disassemble top down. Upon removal of the discharge it was apparent the plastic disc at the top of the discharge was sheared off. Located the schematic at PartSelect and ordered the discharge. Received part within 3 business days and installed new discharge in about 30 minutes. Required 5/16 socket and hex head driver. Recommend ordering new gasket with part.

Door would fall open

  • Customer: Margaret from New Orleans LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

Latch on soap dispenser door broke

  • Customer: Ronald from Longmont CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

The inlet valve on hte dishwasher was bad

  • Customer: Scott from menan ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 12 people found this instruction helpful
I simply connected the two hoses to the valve plugged in the two wires and it was working!

A sudden puddle of water under the dishwasher

  • Customer: George from Asheville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.

dishwasher wouldn't complete cycles

  • Customer: david from simsboro LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
First I removed the screws that held the door together. I then unplugged all the wires from the back and removed the screws holding the LED panel in and unsnapped it from the clips. Just reverse the process putting the new one in. Worked great.

no water going into the dishwasher jet,I could hear the valve hum,but no water through the valve

  • Customer: william from defiance OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 3 of 3 people found this instruction helpful
I first removed both lower front shields,(4 screws)
I then shut off water supply to inlet valve from hot water supply. I removed the water hose from inlet valve,two electrical terminals,( I put tape on right side terminal and lettered with an R as not to mix up the two terminals)removed the hose clamp,removed valve from frame.I reinstalled in reverse procedure.I turned the water back on and checked for leaks.I started the normal cycle and water flowed into the dishwasher as designed.

REPLACED RACKS, LOWER RACK HAS DESIGN FLAW

  • Customer: GREG from Castle Rock CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Replaced upper and lower racks. The new lower rack has a design flaw: it has 3 wheels on each side, but should have 4 wheels on each side. When you pull out the bottom rack, the last set of wheels drop down into the open space where the door hinges to the cabinet, causing the dishes to bounce and shake around. Then when you push rack in, you have to lift it back up onto the tracks made for the wheels to roll on. You can't pull the bottom rack out far enough to access the back of the rack very well.

Dishwasher not getting dishes clean

  • Customer: Matt from Middletown MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 3 of 3 people found this instruction helpful
Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.

water not flowing into dishwasher

  • Customer: Doug from Cornish ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 4 of 6 people found this instruction helpful
turn off breaker
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!

No Water caused soap to not dispense & no clean dishes.

  • Customer: Robert from Brookdale CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 3 of 3 people found this instruction helpful
I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.

Loud grinding noise when dishwasher was draining

  • Customer: Joann from Oakland OR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 3 of 3 people found this instruction helpful
1. Print out the "pump and motor" exploded diagram and label the numbered parts down to #11 (discharge housing assembly).

2. Unscrew the "lower spray arm cap" (#34) by hand (it just twists off), remove the "jump up nozzle" (#1), and lift the "lower spray arm" (#2) and filter guard" (#36) out together.

3. With a torx screw driver, remove the screws holding the "pump cover and secondary filter assembly" (#4), taking note how the assembly was positioned. Be careful not to lose the two plastic "lower spray arm seals".

4. Lift out the "pump housing filter" (#6) and "rinse arm assembly" (#7).

5. With a 5/16 wrench, remove the bolts holding the "discharge housing assembly" (#11). You will likely find a plastic disk just sitting there under the discharge housing assembly. This is the source of your problem. It is the lower plate that has worn loose from the rest of the assembly and the noise is from it being ground by the impeller below.

6. The simplest fix is to order a new "discharge housing assembly" along with gaskets #37 - O-ring (for "pump cover in step #3. Mine was missing.) and #38 - "upper discharge housing gasket. Three parts to order and save your exploded diagram for when you put it back together.

7. Remove the "discharge housing nut" at the top of the old discharge assembly, lift off the "wash arm support", and put both on the new discharge assembly.

8. Insert new seals where they belong and reassemble the dishwasher in reverse order.
All Instructions for the JDB8910AWS
76-90 of 596