JDB8910AWB Jenn-Air Dishwasher - Instructions

Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.

Easiest ever. Recycled the old one and put the new in its place. We are trying to place the silverware in, rather than dropping it in. It was suggested in the video from this website.

Watched video, very helpful. Pulled dishwasher out a foot from counter, which was the most difficult part due to tight fit, carpet, and copper tube water connection. Once the washer was out it was easy to replace the linkage and while it was out did both sides.

I pulled out the dishwasher. Saw that a plastic part linking the door and spring was broken.I was able to ID the part easily on PartSelect. The part came quickly and was installed within 30 minutes. Dishwasher feels like new.

Found picture of the "stack" of pieces online. Decided to give it a try and started disassembling the parts. When looking for replacement parts, found the video @ PartSelect. Wish I had seen it before, but it confirmed I did everything right. It was refreshing to see a step by step instructional video, made everything look easy and it was! Replaced the part and followed the suggestions of the video about replacing the gasket as well and what parts to clean while working. Great help. Very pleaased with the speed of the whole process. Ordered the piece on Sunday, had it on my doorsteps on Tuesday!

The dishwasher would hang up after about 10-15 min. on auto wash. You could hear the control board click but the pump wouldn't start. Ran the diag. process and it came up turbitity sensor. Found one on e-bay (no longer available from parts houses)put it in and had the same problem, this time the error was low motor voltage. Found, from others talking about the same problem on the net, that there were two other things to look for. One is where the wires go out the bottom of the door. The way the machine is designed after time the door will start to cut through them. Taped up any cut wires and made sure the connection was still good. Second, check the back of the control board for cold or loose solder joints. I found two for sure that were cold and the pigtail was also loose. Re-soldered the connections and ran a full cycle with no problems. The solder connections were most likely the problem to begin with. Hope this helps.

Tray outside of dishwasher----Just opened bags and carefully pressed on --- be careful with metal slide stops

I slid the dishwasher out about a foot and easly replaced the Door Spring Linkage. I took more time to remove and replace the screws than it did to replace the Door Spring Linkage. Very easy repair that anyone can do.

We took the hoses off, cleaned all the hard water deposits and screens. The water would fill once but not a second time. We ordered the water valve and valve switch. We put the new water valve on and "miracle" it worked perfectly. We didn't need to replace switch. Let me tell you this is one happy housewife now. Ordering the parts on-line was very easy and they arrived as they said they would. Thanks for the great service.

Replaced The part. Picked up the old one and repurposed it in the work shop and dropped in the new one ...no tools needed. The real story here is that this web page existed and I was able to get the exact replacement part I needed delivered to my house.Piece of cake,

Replaced silverware basket. Works as designed. Speedy part delivery and great service!

The hardest part was figuring out how to get the dishwasher out from the cabinet. Your instructional video said "no tools are needed" but that turned out to be untrue.

removed old rack removed spray tower by twist of my hand reinstalled same and placed lower dish rack back in the dishwasher. It was just hat simple.

I had to get my son to twist off the spray tower, the otherwise the transition to our new racks was quite easy. I did have to look up on the internet Maytag site how to get the spray tower off and how to install a side piece on the upper rack. Easy to do however.

Ordered parts and referred to exploded component drawings on the website to install replacements. Videos were helpful. Be careful to check all plastic parts for deterioration so that you can order them all at once. I had to make two additional orders for rollers and retainers that looked fine, but were brittle and needed replacement.