Models > JDB6510AWP > Instructions

JDB6510AWP Jenn-Air Dishwasher - Instructions

All installation instructions for JDB6510AWP parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB6510AWP
91-105 of 614
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud grinding noise when dishwasher was draining

  • Customer: Joann from Oakland OR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 3 of 3 people found this instruction helpful
1. Print out the "pump and motor" exploded diagram and label the numbered parts down to #11 (discharge housing assembly).

2. Unscrew the "lower spray arm cap" (#34) by hand (it just twists off), remove the "jump up nozzle" (#1), and lift the "lower spray arm" (#2) and filter guard" (#36) out together.

3. With a torx screw driver, remove the screws holding the "pump cover and secondary filter assembly" (#4), taking note how the assembly was positioned. Be careful not to lose the two plastic "lower spray arm seals".

4. Lift out the "pump housing filter" (#6) and "rinse arm assembly" (#7).

5. With a 5/16 wrench, remove the bolts holding the "discharge housing assembly" (#11). You will likely find a plastic disk just sitting there under the discharge housing assembly. This is the source of your problem. It is the lower plate that has worn loose from the rest of the assembly and the noise is from it being ground by the impeller below.

6. The simplest fix is to order a new "discharge housing assembly" along with gaskets #37 - O-ring (for "pump cover in step #3. Mine was missing.) and #38 - "upper discharge housing gasket. Three parts to order and save your exploded diagram for when you put it back together.

7. Remove the "discharge housing nut" at the top of the old discharge assembly, lift off the "wash arm support", and put both on the new discharge assembly.

8. Insert new seals where they belong and reassemble the dishwasher in reverse order.

Our 16 year old dishwasher's top rack lost most of the coated metal 'prongs' that separated/supported items on the upper rack.

  • Customer: Cheryl from White Lake MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
With a straight edge screwdriver I carefully removed the plastic end caps on the rack support glider-shelves, replaced the old rack with the new rack, and then reattached the end caps.

I felt better about ordering the part Online after having talked to a sales person since there were several racks from which to choose. She reassured me that I was ordering the correct part number. I am a woman and 62 years of age, and I was pretty sure this installation would be a no-brainer. I just wanted to make sure I had the right part for the job.

Water Leaking from Door

  • Customer: Kurt from Renton WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 8 of 18 people found this instruction helpful
The lower spray arm of this model has a chronic problem with the plastic seams splitting and the horizontal blast causing door leaks. This was the third spray arm replaced on this unit. Rather than simply replacing the spray arm with the OEM device purchased, I used a solder gun to reweld the seam on the spray arm. I expect that the additional welding will provide many more years of service than the OEM replacement part. They should really improve the quality of the replacement part to prevent splitting. A metal replacement would be worth $50 and provide a better repair than the plastic arm.

Two broken lower rack wheels

  • Customer: Mark from Centreville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol

Wash cycle would stop and hum like it tried to start.

  • Customer: Roger from Marshville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Repair was simple. Diagnosis was wrong. Switch did not fix problem. Most likely a control electronic assembly.

Dishwasher door was slamming down, heavy to close

  • Customer: David from Philadelphia PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

no water entering the dishwasher

  • Customer: frank from mountain home AR
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 3 of 4 people found this instruction helpful
Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

Remove and Replace Door Spring Linkage

  • Customer: John M from Norwalk CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
1) Emptied Dishwasher (roll-around model)
2) Tipped it onto its back
3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver)
4) Opened Door to access side panel (careful not to let it drop on my fingers)
5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring.
6) Removed broken link
7) Installed new link and spring noting the spring direction from the spring on the other side of the door.
8) Pulled spring over the bottom rail bracket with pliers.
9) Reinstalled panels in the reverse order.

Leak in motor shaft seal

  • Customer: James from Houston TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set, Wrench(Adjustable)
  • 3 of 4 people found this instruction helpful
We had had a slow leak on our dishwasher for some time. We were also getting a film left on the dishes and they did not appear clean. Eventually the leak got worse and I had to find the problem. It turned out that in addition to the motor shaft seal leaking, the heating element was out and the installer had done a really bad job, with leaks in the fittings and the wiring not installed properly.

I tried to get the parts locally but they were not in stock and needed a week to arrive. With family coming to visit, I ordered the parts from Parts Select on Monday and they arrived Tuesday. That afternoon, I had everything back together and it is working great.

rinse dispenser was clogged and unusable.

  • Customer: Stuart from Rockaway NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

Rusting lower dish rack

  • Customer: Douglas from Santa Ana CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
The replacement of the rack was straightforward, but the tower assembly had to be moved to the new rack. The fit is precise and fits only one way.i did break off one tab, but it is held just fine.

.

snap spray retainer had broken; sprayer arm had fallen off

  • Customer: Claudia from Highlands Ranch CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Inserted snap spray retainer through center of sprayer arm, snapped whole thing into place, and I was done!

detergent dispenser door latch not holding

  • Customer: fred from henderson NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

Adjustable rack had broken

  • Customer: Richard T. from Atlanta GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
Simply had to replace the clips in the correct position. Would have been a five minute job if I had noticed which way around the old parts went before removing them from the dishwasher to find replacements. It's amazing hoe many permutations there were before it all fit together perfectly.

Tjhe nylon piece that attaches the spring to the door broke.

  • Customer: Herbert from Mechanicsville MD
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 2 of 2 people found this instruction helpful
Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.
All Instructions for the JDB6510AWP
91-105 of 614