Models > JDB6510AWP > Instructions

JDB6510AWP Jenn-Air Dishwasher - Instructions

All installation instructions for JDB6510AWP parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB6510AWP
76-90 of 593
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No Water caused soap to not dispense & no clean dishes.

  • Customer: Robert from Brookdale CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 3 of 3 people found this instruction helpful
I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.

Loud grinding noise when dishwasher was draining

  • Customer: Joann from Oakland OR
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 3 of 3 people found this instruction helpful
1. Print out the "pump and motor" exploded diagram and label the numbered parts down to #11 (discharge housing assembly).

2. Unscrew the "lower spray arm cap" (#34) by hand (it just twists off), remove the "jump up nozzle" (#1), and lift the "lower spray arm" (#2) and filter guard" (#36) out together.

3. With a torx screw driver, remove the screws holding the "pump cover and secondary filter assembly" (#4), taking note how the assembly was positioned. Be careful not to lose the two plastic "lower spray arm seals".

4. Lift out the "pump housing filter" (#6) and "rinse arm assembly" (#7).

5. With a 5/16 wrench, remove the bolts holding the "discharge housing assembly" (#11). You will likely find a plastic disk just sitting there under the discharge housing assembly. This is the source of your problem. It is the lower plate that has worn loose from the rest of the assembly and the noise is from it being ground by the impeller below.

6. The simplest fix is to order a new "discharge housing assembly" along with gaskets #37 - O-ring (for "pump cover in step #3. Mine was missing.) and #38 - "upper discharge housing gasket. Three parts to order and save your exploded diagram for when you put it back together.

7. Remove the "discharge housing nut" at the top of the old discharge assembly, lift off the "wash arm support", and put both on the new discharge assembly.

8. Insert new seals where they belong and reassemble the dishwasher in reverse order.

Dishwasher not getting dishes clean

  • Customer: Matt from Middletown MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 3 of 3 people found this instruction helpful
Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.

Our 16 year old dishwasher's top rack lost most of the coated metal 'prongs' that separated/supported items on the upper rack.

  • Customer: Cheryl from White Lake MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
With a straight edge screwdriver I carefully removed the plastic end caps on the rack support glider-shelves, replaced the old rack with the new rack, and then reattached the end caps.

I felt better about ordering the part Online after having talked to a sales person since there were several racks from which to choose. She reassured me that I was ordering the correct part number. I am a woman and 62 years of age, and I was pretty sure this installation would be a no-brainer. I just wanted to make sure I had the right part for the job.

original basket fell apart

  • Customer: D from Villas NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

The dishrack guide rali stop had come off one of the guide rails, so the wheel in the guide rail would often roll right past the end of the rail, causing the rack to pitch down. this was rather frightening with the rack full of glasses and other breakables.

  • Customer: Margaret from New Ipswich NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
At first I snapped the plastic piece together and then tried to put it in the guide rail. That's where the sharp knife came in handy, to pry the piece apart again and start over. It was easy to see how the piece was supposed to go into the end of the rail and snap in place; I just didn't look carefully before I had to backtrack! I haven't yet tried to put in the other pieces we ordered.

Washer made grinding noise at end of drain cycle

  • Customer: Peter from Long Beach CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 3 people found this instruction helpful
Initially I suspected something had found its way to the impeller or the macerator, began to disassemble top down. Upon removal of the discharge it was apparent the plastic disc at the top of the discharge was sheared off. Located the schematic at PartSelect and ordered the discharge. Received part within 3 business days and installed new discharge in about 30 minutes. Required 5/16 socket and hex head driver. Recommend ordering new gasket with part.

Door would fall open

  • Customer: Margaret from New Orleans LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

Latch on soap dispenser door broke

  • Customer: Ronald from Longmont CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

The inlet valve on hte dishwasher was bad

  • Customer: Scott from menan ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 12 people found this instruction helpful
I simply connected the two hoses to the valve plugged in the two wires and it was working!

A sudden puddle of water under the dishwasher

  • Customer: George from Asheville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.

no water going into the dishwasher jet,I could hear the valve hum,but no water through the valve

  • Customer: william from defiance OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 3 of 3 people found this instruction helpful
I first removed both lower front shields,(4 screws)
I then shut off water supply to inlet valve from hot water supply. I removed the water hose from inlet valve,two electrical terminals,( I put tape on right side terminal and lettered with an R as not to mix up the two terminals)removed the hose clamp,removed valve from frame.I reinstalled in reverse procedure.I turned the water back on and checked for leaks.I started the normal cycle and water flowed into the dishwasher as designed.

NO WATER INTO THE DISHWASHER

  • Customer: RICHARD from RAMSEY NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 3 of 3 people found this instruction helpful
turned off water at valve, removed float switch, removed water inlet vlv. replaced and reassembled. still not water going into the machine. i have no voltage to the valve or float switch. i then took the door apart to find there were burnt wires as well as a burn mark on the control panel. upon closer inspection, it looks like the door seal has failed and water got into the door. had to replace dishwasher with a new one.

Motor made a loud noise when running

  • Customer: Earl from Slatington PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 5 of 9 people found this instruction helpful
First I turned off the circuit breaker to dishwasher. Then removed the lower spinner and related parts. The water in the bottom needs to be sucked out with a shop vac next, because when the pump screws are removed any remaining water will drain underneath onto the floor. Remove the wash pump and drain rotor.
Remove the front bottom plate to access underneath, unplug the electric motor and thermister. Unscrew both hoses,drain and upper wash arm. Move the locking ring to release the the entire assembly up into the dishwasher.
The kit I bought had most of all the washer parts included, so on reassembly I used the new ones. The rest when back together in reverse order after a good cleaning. Since the thing was apart anyway why not clean up all the filters on reassembly. The kit also came with complete instructions.

detergent dispenser door latch not holding

  • Customer: fred from henderson NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.
All Instructions for the JDB6510AWP
76-90 of 593