Models > JDB6510AWP > Instructions

JDB6510AWP Jenn-Air Dishwasher - Instructions

All installation instructions for JDB6510AWP parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB6510AWP
31-45 of 593
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

diswasher would not drain

  • Customer: Larry from Arlington VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 15 of 22 people found this instruction helpful
1) turned off power to dishwasher
2) removed each piece of pump assembly (one at a time) from inside the dishwasher. I had no repair manual and didn't know that by rotating the lock lever under the dishwasher, I could have easily removed the entire pump assembly as a unit.
3) Reassmebled the pump assembly using new parts and installed in dishwasher.
4) Reconnected hoses and electrical connection
5) Turned power back on
6) Washed dishes... it's as good as new!!!!

The basket in our dishwasher had many broken parts on the bottom and the silverware kept falling through

  • Customer: Marge from Cranford NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 13 people found this instruction helpful
We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

Machine began making noise as if something had let go and was beating on the machine

  • Customer: Michael from Lost Creek WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
I removed the plastic retainer that held the lower spray arm in place. After removing the lower spray arm I was able to remove the 6 hex screws that held the cover over the filter screen and the discharge housing assembly. I was then able to remove the bolts that held the upper part of the discharge housing assembly, and replaced it with the new part that I received. The rest of the job was simply putting it back together.

Note: While repairing the broken part, I noticed a small leak under the machine around the float assembly. This was simple to fix. Remove the small lock ring on the bottom of the float. Pull the float out and clean the grease and soap scum out of it. Put it back in and attach the lock ring. No more leak and the water gets turned off when the float activates the switch. Something that everyone should check periodically.

Racks were rusted and the tines were breaking off

  • Customer: Loraine from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 17 people found this instruction helpful
The bottom rack was easiest, just picked it up out of the dishwasher and moved the sprayer and the silverware holder from the old rack to the new rack and set it back in the dishwasher. The top rack was a little tricky, it took a minute to figure out to remove the little end-caps on the runners and then it just slid out. Slid the new one in, replaced the caps and moved the upper rack basket. It took less than 15 minutes to fix and now it's like a brand new dishwasher!

Plastic door handle broke

  • Customer: William from Austin TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench set
  • 11 of 11 people found this instruction helpful
It is an easy repair, but you need the right tools to remove the inside of the dishwasher door (a hex wrench set) and then to remove and replace two screws holding the plastic door handle in place (1/4 inch Allen wrench). Make sure the power is off even for this repair because it can't be done without coming close to electrical elements.

Rusted upper and lower racks, broken tines

  • Customer: Charles from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
Read the experiences here, very helpful. Bottom slides out first - really easy. The new part comes with rollers, you don't need to remove the old ones. Now the only problem, getting the sprayer off the bottom basket. Look carefullty, you must use a screwdriver to release one side of the sprayer, then it works off easily. Make sure you note the orientation of the base of the sprayer. Reverse steps above and you are done. New tray slides in. Our new tray was a bit wider than the old one so we needed to use a bit of pressure to "shrink" the back just a wee bit.

The upper is easy also. Since the rails are uneven, make sure you put the high rollers on the high side no matter what your wife told about how it is supposed to go in. The end caps snap inward and slide out of the rails. Easy once you know. The uneven rails are obvious once you notice. Total time was 45 minuts, 30 of which was figuring out how to get the sprayer off without damage.

Would be nice to know the factory recommendation for removing the sprayer.

Dishwasher had weak drainingf pressure, turned out to be the drain impeller.

  • Customer: William from Beaverton OR
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 11 of 12 people found this instruction helpful
After I ruled out a hose blockage I looked in the washer.

Took the washer assembly apart, pretty straight forward, used the parts diagrams on this site for help. Found the drain impellor was jammed with glass and had lost a lot of its fins.

Found exactly what I needed here. Had it back together in less than an hour, and it seems to be working like new.

loose top basket/

  • Customer: Wanda from Bay Shore NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 23 people found this instruction helpful
I had two problems with the dishwasher. The top basket was loose, but the main problem was a plastic part inside the bottom assembly.

The part was backordered, so I re-ordered it through Sears. They said it would arrive in two days. Theirs came in two weeks, and their customer service was terrible.

Your "backordered" part came in two days, even before it was supposed to come had the part not been back ordered. I am delighted with your customer service and your company.

The illustrations on your website were excellent. They helped us not only to identify the part, but to diagnose the problem.

This was my first purchase through your company and if I ever need parts again, there is absolutely no reason to go anywhere else.

You have an excellent company, and great website! I bookmarked your page for future purchases.

No water in the washer barrel

  • Customer: Terry from Great Falls VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 10 of 11 people found this instruction helpful
Diagnosed potential problem from scematic diagram found at Parts Select .Com by entering model #. It was very likely the inlet water solenoid. Tear down was simple: Turn off water, disconnect water lines to and from solenoid, disconnect two electric terminals and remove part by removing two screws from dishwasher chasis. Before you buy the new solenoid, unscrew the water inlet elbow from solenoid and check the filter/screen inside the solenoid to make sure it isn't clogged. Assuming it's not, order the replacement part and reinstall in reverse order. Be sure to use plumber's tape on screw connections to make sure there are no leaks..... Also for ease of acces, you'll need to turn the dishwaher down on it's front. Put towels down to cushion the front and keep the controls from contact with the floor. Good luck!!

Pump gasket had deteriorated with age and causing odors.

  • Customer: Kenneth from Brooks GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 9 of 9 people found this instruction helpful
The dishwasher is well engineered to perform this work.

Remove the bottom two panels to provide access and visibility to base of pump motor.

Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.

Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.

From below raise pump motor and support with block (piece of 2x4 worked well).

insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.

From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.

re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.




I

heating element split open

  • Customer: Hadley from De Leon TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 9 of 9 people found this instruction helpful
I took the bottom cover off and pulled off 2 wires and removed 2 plastic nuts. I removed the old part and removed the O rings from the old part and installed the new heating element. Replaced the plastic nuts and the two wires. It was very simple. The hardest part was lying on my back to get to the wires and nuts.

Racks were rusting, pieces braking off and rubber coating was peeling.

  • Customer: Lora from Plover WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 36 people found this instruction helpful
Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.
We will recommend your site to friends.

Noise after water disharge.

  • Customer: Nidhal from Hillsborough NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
Using the part list (on your web site)as a guide to remove the parts,Part 32 remove by hand turning counter clockwise,remove screws #5,remove parts(33,34,31,2).
Remove #36 remove 4,3,,6,7,,8,9,remove screws#27 then remove #11 which has a plate part of it but broke on the underside (you can't see it in the picture)it will rub on the fins of part#14 during the cycle when dishes are being washed creating a grinding noise.
i Do suggest to replace the seals,38,37,you may coat the new seals with liquid hand soap for easier installation.

Not getting clean dishes; filter kept getting cloged.

  • Customer: Joe from Titusville NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
After removing parts, cleaned both upper and lower spray arms, blew out lead to the upper arm, and started to install the new parts.

Unfortunately, the Pump Housing Filter was still cold (freezing weather during shipment and left at the front door) and when I started to bend it into shape it broke in two places. So I tolk the old filter and some Lime away and slowly cleaned it with soft brush to open 95% of the holes.
Once ready it was installed along with the other new parts and the dishwasher works very well.

Simple homeowner repair.

dishes still dirty, soap remained in dispenser.

  • Customer: Hans from Show Low AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 11 people found this instruction helpful
After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.
All Instructions for the JDB6510AWP
31-45 of 593