Models > JDB2100AWS > Instructions

JDB2100AWS Jenn-Air Dishwasher - Instructions

All installation instructions for JDB2100AWS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB2100AWS
16-30 of 227
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The impeller was not spinning. There was no washing water.

  • Customer: Brian from Portland OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 9 of 10 people found this instruction helpful
After finding out that the impeller shaft was stripped (plastic) I quickly found the correct replacement on partselect.com by using my model number.
You do not have to remove the dishwasher, if you know what is wrong. But, throw the breaker switch and turn off the water! After removing the spin washer arm, Undo all of the torx screws and pull out the plastic filter looking plates along with the center plastic water jet. This jet provides water for the upper washer assembly. You may have to pop that upper assembly out to protect it from damage.
The black impeller should just pull out if the plastic shaft is stripped. Otherwise, unscrew the small torx head and remove the impeller. You can remove the blade at this time and unscrew the plastic shaft by unthreading it while keeping the motor from spinning. (I shoved a screw driver underneath the dishwasher through the motor. Also the motor is just floating on the rubber gasket and can easily pulled out to accomplish this task. It's heavy and has a plug attached to it. You'll see where you can shove the screw driver. This comes in handy while installing the new shaft, because it is metal. Which is a great, long awaited upgrade for the Maytag Quiet Series. Once you find which shaft to use, (which correct inner thread, course or fine), install it with the great directions that come with the part. Putting all the stuff together is not as bad as one would think, there is only one way for it to go back together. After installation is complete, turn water and breaker switch back on. Run a cycle and listen for the washing cycle against the wall of the washer. If you cannot tell the difference, you can unscrew the white lock arm and insert it into the door. Turn it on and watch how a dishwasher works. Get ready to get a little wet. Towels!

Weeping water control valve

  • Customer: Robert from Woodstock IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 8 of 8 people found this instruction helpful
Turned off water and power to the unit. Removed kick plate from under the dishwasher to access the water contol valve. Placed an absorbant rag under the water valve and water line. Disconnected solenoid on water control valve from electrical connection with my fingers. Used a standard adjustable wrench to disconnect the water line from the water control valve. Then used a 1/4" nut driver to loosen the two bolts that hold the water control valve on to the mounting bracket. Pulled the water control valve slightly forward to disconnect the water feed line to the dishwasher. Used a blunt end plier to pinch the clamp open and slowly wiggle the feed line off of the water control valve. Then removed 90 degree elbow off of the water control valve and used pipe dope and connected the elbow onto the new water control valve. Replaced water control valve in reverse order and utilized new hose clamp to reconnect feed line to new water control valve. Saved door seal for future use, when seal goes bad.

dishes still dirty, soap remained in dispenser.

  • Customer: Hans from Show Low AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 14 people found this instruction helpful
After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.

Dishwasher heating element bad

  • Customer: Gary from Indianapolis IN
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 8 of 10 people found this instruction helpful
I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.

the soap dispenser wouldn't open during cycle

  • Customer: paul from spring hill TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 7 of 8 people found this instruction helpful
I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

dishwasher stopped working

  • Customer: Kenneth L from Kansas City KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 7 of 9 people found this instruction helpful
Symptoms: our dishwasher stopped working and the door would not close. My first response was to change the door switch, since it was closing really hard and the switch was much cheaper than anything else on the list of parts.

Well, that failed to correct the problem. After double checking all the connections and having a door that now closed much better, the dishwasher still didn’t work. The circuit was good so it must be a bad fuse, relay, or power supply right? Didn’t find any, but while I was looking I found some testing instructions taped inside one of the panels and half way down the page it said, “If control fails to perform as described, replace control.” Well it definitely didn’t perform and one test caused some panel lights to come on so I knew I had power to the control panel.

I swallowed hard and shelled out the cash. The hardest part about replacing the control panel was figuring out that the outside door panel was attached to it and after removing the 3 screws at the bottom, you can just pull up on the outside door handle and the whole thing comes off. Use the same screws and adjust for a snug fit. One other thing is that the control board has a slider to lock the ribbon cable firmly in place.

I’ve included one page on the testing instructions which helped identify the problem. Good luck, Mr. Fixit.

Motor would not turn the impeller, no wash pressure.

  • Customer: mark from blackwood NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
Not a bad repair once you diagnose the problem. Took me three tries to figure it out. Just make sure you follow the instructions. I used an allen wrench to hold the motor in place while tightening the part onto the motor shaft, this way I didn't have to remove and flip the dishwasher to do the repair. The good news is the replacement part I needed was metal instead of plastic, thus I should never have this problem again. I don't understand why it was plastic in the first place but all of my appliance problems seem to be made to fail after several years of service.
Repair was

Dishwasher leaking water

  • Customer: Marvin from Republic MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 8 of 12 people found this instruction helpful
Pulled the dishwasher out. Determined that it was leaking from the air/water inlet. Ordered the seal and replaced the seal by turning the inside cover counter clockwise while holding the outer water inlet. Replaced seal and installed water hose. Put dishwasher back inside cabinet and leveled. If you don't try to fix it yourself, It could cost more then what it is worth.

Door latch on the dishwasher broke.

  • Customer: Christopher from Porter IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
First I opened the breaker on the dishwasher removing power from the unit. Then I removed the Torx head screws on the cover on the back side of the front door. Then I pulled off the stainless steel sheet metal panel which exposed the door latch. Then I unplugged the electrical connectors to the two micro switches on the assembly, next I plugged in the connectors on the new latch assembly and postioned the latch back on the mounting holes. Replaced the stainless steel sheet metal and put the screws back.

Closer tab on the door broken.

  • Customer: Paul from Austin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if I need to change it in the future.

upper shelf dragging on slides ball bearing cage broke

  • Customer: paul from worcester MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 13 people found this instruction helpful
remove shelf install ball bearings in new ball cage click ball cage into slides re-install shelf piece of cake make sure you have all the ball bearings when ordering the cage they dont come with it 4/cage

drain line had split

  • Customer: William from Interlochen MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 8 of 13 people found this instruction helpful
disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

Very little water going into the dishwasher

  • Customer: Ralph from Taft CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 7 of 10 people found this instruction helpful
Unpluged the electric, Disconnected the water line and the drain line. Removed the dishwasher. Removed and installed the new water inlet valve and the float switch. This was a very simple repair. Reinstalled the dishwasher and connect
the water and drain line. Pluged in the power line. Turned the dishwasher on and it worked perfect. Thank you for the correct parts.

The door would just flop down when you opened it

  • Customer: David from Plano TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.

Upper Rack not Cleaning

  • Customer: Stephen J from Sammamish WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.
All Instructions for the JDB2100AWS
16-30 of 227