Models > JDB2100AWB > Instructions

JDB2100AWB Jenn-Air Dishwasher - Instructions

All installation instructions for JDB2100AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB2100AWB
46-60 of 217
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

detergent dispenser door latch not holding

  • Customer: fred from henderson NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

Machine would not fill with water

  • Customer: David from Farmingdale NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 4 of 7 people found this instruction helpful
Remove the 4 screws at the lower panel, turn power off to dishwasher, remove single 1/4 attaching screw from float switch, open the door remove the old float assembly. Make sure you install the float in the machine first than side the switch over the end of the float before screwing it back in.

Soap dish full of west soap, dishes not clean: Isolated to stripped pump shaft, foreign object jammed chopper

  • Customer: Tom from Centreville VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.

Rollers on adjuster were loose because plastic was broken inside where screws were attached

  • Customer: Yvon from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
remomed old adjuster and attached the new one to the housing and it was done it was very simple

Door handle stopped engaging

  • Customer: Harold L. from winamac IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

The fold away tine clip snapped and had to be replaced

  • Customer: Lisa from Malvern PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
I snapped off the 2 old parts, ordered the new ones and snapped them back in, however, the new parts are not the same as the old ones and do not do the job of holding the collapsable tine rows up...now they just fall over. Guess I have to call Jenn Air.

Original silverware basket bottoms fell out

  • Customer: John from Mooresville NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
It's great having a firm like PartSelect.com at your disposal. Part identification using your schematics was as simple as ordering the parts. I've told many people about your exceptional customer service and ease of use!

I just pulled out the old baskets and repositioned the new ones from PartSelect.com. No tools were needed!

The dishwasher got the dishes dirty not clean

  • Customer: Ken from Mapleton UT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

Door would not close because latch was not working

  • Customer: Michael P from Greenville TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
I turned off the electricity at the circuit breaker. Sitting in a chair in front of the opened dishwasher with the partially opened door resting on my knees, I removed the 10 screws lining the inside of the door (setting them in order on the cabinet above -- 2 are different length so this helps keep them in order.
I tilted the inner cover on the door up (which is what the screws had been holding). With the door not fully open because it was on my knees, I was able to position the cover so that I did not have to remove the connection to the soap dispenser.
The two middle screws removed earlier were the screws that held the latch in place, so the assembly was already loose at this point. I put a black mark on the assembly to mark the side that the black wires were attached. Then with the pliers removed the plugs that were connected to the switches on either side of the assembly. Then marked the replacement assembly with the black mark on the same side as the one removed. I attached the plugs to the the replacement assembly using the black mark as reminder for which side was which.
I lined up the latch on the door where it goes, lowered the lid (lifting the lower edge over the base a little), lined up and started the latch screws (middle 2), then started all of the other screws and then tightened them all. Closed the lid and tested the latch. It was closing correctly now. I turned on the electricity and tested to make sure all was now working properly.

Latch Asembly Broke, Door wouldn't close properly

  • Customer: Sam from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.

Dishes weren't getting clean

  • Customer: Bill from Maple Valley WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Maytag should be ashamed to put such poor plastic material in an otherwise good design. The seals that join the rotary sprayers to the rear wall had hardened and crumbled away. When I discovered that water pressure had been lost at the spray arms, it was a simple fix. Snap off the failed parts, pay Partselect $37 because Maytag wanted to save a dime and snap in the new parts. (Parts that will fail again in another 3 years.)

dishes had small bits of food stuck on

  • Customer: angela from Powell OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.

Dishes not getting clean. Tear in the filter.

  • Customer: Harry from camas WA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 2 of 3 people found this instruction helpful
Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

Cups and glasses on upper rack were not getting clean.

  • Customer: Douglas from Pickerington OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

Wouldn't wash dishes

  • Customer: Ed from Orlando FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.

Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!
All Instructions for the JDB2100AWB
46-60 of 217