Models > JDB2100AWB > Instructions

JDB2100AWB Jenn-Air Dishwasher - Instructions

All installation instructions for JDB2100AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JDB2100AWB
196-210 of 227
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Very little water getting into the machine, would not clean .

  • Customer: john from crisfield MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
First turn off power and water then Removed the two screws on the bottom plate, took the plate off. To remove the valve , I took one screw out of the bracket and just loosened the other,Pulled the valve out ,removed the water lines,then reused existing brass connection, put the hoses on the new valve then put it back together .Turned the water on checked for leaks, then closed it up..Turned the power on and it works great.....

Water was only filling once in a while with water

  • Customer: Timothy from WHITE CLOUD MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
my dishwasher is located in a island so i pulled the paneling off the back & the covers off the bottom of the dishwasher. my water shut off is under the dishwasher. i shut it off unhooked the water line at the union shut off the electric, unpluged the valve, pulled 4 screws out of the valve bracket , slide the clamp off the hose and removed the hose from the valve took the valve unit out removed the water line from the old valve put it on the new valve reassembled it turned water on checked for leaks turned the electric on and tried it out.

Tine latch: Upper Deck Front portion broke

  • Customer: Sarah from Dunlap IL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The rack threads through this part. I needed to remove the rack along with this part by carefully unlocking the rack through its rear latch. Then I removed the protector cap of the portion of rack sticking through tine latch. Then carefully withdrew the rack from the tine latch. Then threaded the rack in the same way through the replacement latch. Then attached this latch with the rack to the tray and re-hooked the rear part. ONLY tricky part is to realize that rack needs to be removed along with the tine latch to be able to replace it.

Pump gasket melting and falling apartGetting black marks all over dishes and tupperware

  • Customer: Lou from Selden NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The actual repair was pretty easy except the cleaning of the old gasket. It was melted and smeared all over the place, had to use mineral spirts to clean everything once i removed all the parts. Star screw driver with the power off i removed all the screws down to the pump, unlocked 3 locking clips from below the unit and removed the gasket without having to remove the motor. Cleaned everything and reassembled works perfect. use the diagram of that model to how to reassemble or take pictures

The glasses on the top rack had food particles in them after a wash cycle

  • Customer: David from ocala FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I initially took everything out and cleaned everything with the shop vac, and outside with the garden hose. That did not work, so I looked on parts select for a new accumulator filter, as I was not able to clean that very well. To install the new filter, I removed the sliding racks, top and bottom, and the water manifold, then removed the lower wash arm, then the parts under that, the filter plate, the outlet, the impeller, all the way to the accumulator filter. After removing that, installation was the reverse. I also cleaned the middle washing arm, and the lower, as I noticed food particles blocking the outer holes. All is good now, and the dishwasher, which we use almost every day, is working fine.

The dishwasher door latch was broken and would not hold the door closed.

  • Customer: Ruth from Canyon Lake CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I unplugged the dishwasher under the sink. I opened the dishwasher up and took out the 12 screws holding the inside door facing on. I gently moved the door facing down towards the dishwasher to reveal the door locking mechanism at the top of the door. I unplugged the mechanism and plugged in the new one. I put the door back together the same way I had taken it apart. In all it took about 12 minutes. Works like a charm.

Dishwasher did not clean and drain properly

  • Customer: Noel from Orange TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Routine repair. There are videos on the net that show exactly how to replace the filter unit. However, when you order the filter, order a replacement pump impeller. The impeller must be removed to remove the filter on this model. The impeller was stuck on the shaft, and I had to destroy it with the side cutter pliers to get it off. Before putting the new one on, clean the pump shaft thoroughly and lube the shaft with silicon lube or Vaseline jelly. Clean the bottom of the water pan thoroughly, then reassemble. Then pour one cup of vinegar in the bottom of the dishwasher and run it with no dishes. This will clean the inside of the dishwasher.

Cracked drain hose

  • Customer: Jack from Miami FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Slid washer out from cabinet after disconnecting drain hose from garbage disposal and unplugging from electrical outlet. Was necessary to lay washer on side to disconnect drain hose from the dishwasher. Have towels ready as you will likely have some leftover water in hose & dishwasher. Used tape to secure insulation pad to washer so it would not catch on the side and top of cabinet when sliding back in place. Easy fix.

Our dishwasher was not heating up to dry dishes

  • Customer: Claude from Helotes TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
All steps were easy except the Maytag layout made it hard to get to the fittings to remove and reconnect the water line. After that we just moved the dishwasher from beneath the counter and laid it down on the front. Removing and testing the old heater element was easy. The hardest part of installing the element was the odd clips inside the dishwasher. I need to return the o-ring and nuts because you included them with the heating element.

Sandy looking grit in the bottom of some of the glasses and cups.

  • Customer: Emma from Plano TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the directions on the video. Repair went well, but did not solve the problem.

Door would not close

  • Customer: Micheal from Batavia IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Removed the panels and the part came right out. Easier than I thought. part came faster then expected.

dishwasher door not closing correctly and bad microswitch

  • Customer: Wesley from Glendale AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed 10 torx fasteners.Pulled inner door panel up to gain access to latch. Latch has both micro switches attached. Un plug switches, remove and replace door latch, button up and your done.

Door latch handle failed

  • Customer: Roberto from Cedar Falls IA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Install complete latch and handle assembly. Remove panel, disconnect wiring and install the assembly

Dishes were not getting clean

  • Customer: Michael from Buttw MT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Thank You PartSelect for making this repair project simple and stress free. The exploded diagram of the appliance was clear and consise. The parts list was very helpfull. Showing me which parts were the most replaced gave me the confidence to order, reducing the prospect of having to return items ( always a pain point ). Parts arrived in just a few days. Followed the instructions on the video. Dishwasher was back in operation in no time and passed an overly thourgh dish inspection. Your site is amazing and is on my favorites tool bar. Thanks Agian !!!

water leak at right front coner

  • Customer: NORMAN from BRYAN TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
pulled dishwasher out to see where the leak was comming from . after seeing where it was leaking i searched for parts for jenn-air diahwasher. that when i read about the reviews on how to replace the float switch. it was very helpfull in being able to do the work myself and not having to pay a repairman.
All Instructions for the JDB2100AWB
196-210 of 227