JDB1100AWB Jenn-Air Dishwasher - Instructions

Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together

After noticing that the nozzles in the washer arms seemed clogged, I ordered replacements from PartSelect.com. Installing them was a breeze. The upper arm had a torx screw in it and the bottom just required a nut driver to get off. I replaced the arms and ran some DishWasher Magic through it and now my dishes are clean again!

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

I first listened carefully and noticed that during cycling, the electric motors could be heard starting, stopping, and apparently running normally during both wash and emptying cycles. However, no water was being pumped around during the wash cycles, while emptying (which uses a different motor) worked normally throughout all cycles. Thus it seemed to me that the electronic programming was working correctly in turning both motors on and off as necessary. So I figured somehow the wash motor impella was not turning and pumping water, despite the fact that the motor was indeed running correctly. So I removed all the plastic housings, the screwed on impella, and the metal chopper at the base of dishwasher. Then I was able to easily pry the old plastic chopper sleeve right off of the electric motor shaft (normally it is screwed on and cannot be pryed off). Since the plastic threads inside the chopper sleeve were completely stripped, the motor shaft would turn but the impella would slip on the shaft and not be driven. The replacement sleeve was much better constructed (metal not plastic). It could be easily screwed on to the motor's driveshaft after lifting the old rubber seal and gently holding the motor shaft with a pliers (carefull to avoid scratching the shaft). I removed the old rubber seal nd replaced it with the new one from the kit, right over the newly installed metal chopper sleeve. Next, I easily centered the metal chopper sleeve and pressed in the new seal after reinstalling the plastic/metal chopper screen, using the temporary jig included in the kit. Then the jig was discarded and the impella simply screwed onto the chopper sleeve (using the appropriately threaded hold-down screw provided in the kit). Finally, the rest of the plastic hardware is screwed in place. Waahhlaa...now impella is motor driven again and blows water hard into the dishwasher during the wash and rinse cycles. Total cost of job to do-it-yourself, $29.50 including shipping (which only took three working days). Estimated job if down by appliance repairman, $140 (assuming the repairman didn't first erroneously blame the problem on faulty electronics then charge you hundreds of $$'s to replace circuits which were not broken to begin with, only to find the dishwasher still not washing/rinsing after his expensive electronic circuit replacements. The actually mechanical fix was cheap and simple. Truthfully, there is no excuse for Jenn Aire to ever use a plastic Chopper Sleeve in their dishwashers to begin with.......carefully planned obsolesence if you ask me. Oh well, it works perfect now. I doubt if even the four marbles my 4 year old had tried earlier to wash in my dishwasher (stripping out the original chopper sleeve) would do any damage to the metal replacement. However, I don't plan on testing my hunch. A simple fix, but a slightly challenging diagnosis which relied on a keen sense of hearing and a quiet workplace. Seems many people in these blogs have had the very same problem with their Jenn Air/Maytag dishwashers, and have made the same diagnosis and the same simple fix. Thank you mucho, PartSelect.

Removed the bottom cover.with a flashlight and a mirror found the problem. Went to Maytag they told me that in 8 warehouses there were no parts. They did give me a enlarged view of the part that I needed. went on the computer to PartSelect called PartSelect talked to a very helpfull Lady ordered my parts. Job is done Mama's happy Lifeis good. Thank You

I noticed that the dishes on the top rack were not getting clean. While the dishwasher was running, I opened the door to see if the arms were moving/spraying and they were not. I cleaned the filter and checked the impeller and both were clean and not damaged. After looking how the top rack slides into the "flapper" I took it off to inspect it. It was missing the rubber to make the seal with the tube from the top rack. After replacing this part, the dishwasher is cleaning like new. Here is the part PS2340934 Docking Station with Flappers

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

By reading online about some similar problems, I discovered that the accumulator did, in fact, have some holes worn through the screen and was leaking sediment back into the rinse water. After waiting for 2-3 months because the apart was on back-order at the factory, it took me less that 1 hour to remember how the unit went together (reviewed the parts diagram online) and connect everything up. On the first rinse, the dishes were really clean - well worth the wait. Doing dished by hand reminded me of the old days....

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.