Models > JCD2295HES > Instructions

JCD2295HES Jenn-Air Refrigerator - Instructions

All installation instructions for JCD2295HES parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JCD2295HES
571-585 of 744
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

icemaker quit making ice

  • Customer: Mark from nicholasville KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I first replaced the dual water valve solenoid. The ice maker still refused to work. I then ordered and installed the ice maker part number S106626640 626639 OEM listed for a Maytag D7824706Q ice maker. This was an exact replacement. I swapped out the wires and wire toggle as directed. After plugging it in and approximately 6 hours, it made ice. Be sure to trim the plastic hose ends going to the water valve solenoid to ensure a good seal. I also insisted on using OEM parts, not the less expensive generic replacements. The OEM parts are twice the money but worth it considering my free labor. The installation was not difficult.

broken roller

  • Customer: mark from marcella AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
went by instructions, used a little common sence.

very noisy-sounded like it was shifting gears

  • Customer: curt from ojai CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed freezer trays, drank beer, removed panel, another beer, replaced motor, another beer, replaced panel, one more beer/snacks, cleaned rear of refrigerator(lint/dog hair)dip of copenhagen, plug in, works good!

Ice maker quit

  • Customer: Peter from Johannesburg MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

Ice maker leaked a little, then quit completely.

  • Customer: Steve from Lansing MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

Freezer was frozen over

  • Customer: Kathryn from Gordon NE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I popped out the electronic control board and replaced it with the new one. After following the programming instructions provided with the part, the refrigerator/freezer worked great.

Freezer keept freezing with ice buildup and would not automatically defrost

  • Customer: John from Staunton VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I used an internet link that the customer service lady provided to assist me in learning the proper removal method, so I could replace the part. So far this seems to have fixed the problem.

Ice wheelce wheel was broken, ice maker not working and bucket cracked

  • Customer: Edward from Shepherd MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Removed bucket,and removed the front cover. the ice wheel was removed by removing the nut from the blade assembly and removing the blades washers and spacers. The parts were replaced in reverse order and the nut replaced. The ice maker was removed by removing the bottom bolt, loosening the two side bolts and lifting the unit off the bolts. the cover was removed from the ice maker and the tab depressed on the wiring harness which was then unplugged. The wire was removed and replaced on the new unit the harness plugged into the new unit and cover replaced. The unit was the placed back on the bolts, tightened and the bottom bolt replaced. the ice bucket was replaced and unit turned on. Ice making within an hour.

the ice maker stopped working

  • Customer: Patrick from Barnegat NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

Ice maker drips water, making a blob of ice in the compartment

  • Customer: Charles from Metairie LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

Compressor would not run.

  • Customer: Dennis from Grant NE
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was simple. It was a matter of unpluging the old relay and then pluging in the new one. I almost bought a new refrigerator but after doing alittle reading on this web sight and finding out the most common reason for having the problem I was having I decided to order the relay. It was the problem...$ 70.00 -v- $1400.00. I'm HAPPY !

Old ice maker element burnt out

  • Customer: David from Bonita CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

Defrost Cycle noy Functioning

  • Customer: William from Hudson Falls NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Found Board location and replacement instructions on Appliance Doctor website. Price there was actually 3 $30.00 cheaper.Had to remove light cover to access slots to insert a flat blade screwdriver which you use to depress tabs to unlock control board housing. It then swings down so you can unplug wiring harness's and remove and replace control board. Too early to tell if defrost is working yet.

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

Icemaker making icebergs, then nothing.

  • Customer: Edward from Burnt Hills NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The icemaker in my Maytag refrigerator was having a few problems. First, a small leak developed in the ice cube tray, allowing water to drip into the ice bucket. This of course caused the ice to become one solid mass, totally inappropriate for a gin and tonic. After a couple of months of this, it stopped working altogether. On to the internet I went, and discovered how easy this repair actually was. One nut to remove, one to put it back in. The installation video was very helpful. I did have a concern at first because the icemaker did not start making ice rights away. I thought it might be a defective unit. It took about 12 hours to get the first batch and it has been happily cranking out the ice since! Ed in upstate New York.
All Instructions for the JCD2295HES
571-585 of 744