Models > JCD2289AEW

JCD2289AEW Jenn-Air Refrigerator - Overview

Get Parts and Repair Help for JCD2289AEW

If you know the refrigerator repair part you need, you can browse the list of all parts on the JCD2289AEW, or you can search by name or part description. You can also find your part by where it is located on the JCD2289AEW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for JCD2289AEW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$107.31

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

$2.52

Light Bulb - 40W

Sold individually.

$2.70

Screw

This screw is sold individually.

$49.48

Water Filter

This Puri-Clean water filter will fit most Maytag and Jenn Air refrigerators that have a screw-in filter. Sold individually.

$72.81

Adaptive Defrost Board

This part allows the refrigerator to go into defrost mode only when required.

$64.52

Ice Dispenser Solenoid and Door Kit

In addition to the solenoid (115V), this kit also comes with a door strike and an ice door assembly. Please be advised the spring and roll pin are not included with this kit.

$14.89

Water Fill Cup and Bearing

$43.82

Defrost Heater and Thermostat Assembly

This part assembly has 2 functions: The defrost heater keeps the cooling coils from frosting over and the thermostat senses that the heat near the cooling coils has reached the desired temperature.

$3.66

Light Bulb - 40W 120V

Sold individually.

$13.46

Limit Switch - 2 Terminal

This limit switch is located in the ice/water dispenser section. The switch pictured here is black, though this type of switch is also available in white.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 517 of 529 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 205 of 276 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Fridge Side Warm Freezer Fine

  • Customer: james from livermore CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 124 of 130 people found this instruction helpful
Removed the Hex head small screw at the middle back of the Back wall of the fridge above the top shelf. Removed the 2 small Hex Head screws that go into the of the Plastic cover upwards into the top roof of the fridge.
I ended up with an extra screw so I dont know what I did...
The hard part is pushing up on the two tabs, one on each side in the ex... read more