Models > JCB2280HEW

JCB2280HEW Jenn-Air Refrigerator - Overview

Get Parts and Repair Help for JCB2280HEW

If you know the refrigerator repair part you need, you can browse the list of all parts on the JCB2280HEW, or you can search by name or part description. You can also find your part by where it is located on the JCB2280HEW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for JCB2280HEW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

$103.07

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

$36.81

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$6.92

Door Closure Cam Kit

This part helps with the closing of the door and helps keep them in position.

$4.41

Crisper Frame Support

Note: If the wall anchor that this piece mounts on is broken, then the support is needed. (Order per Model#)

$2.70

Screw

This screw is sold individually.

$67.27

Compressor Start Device and Capacitor

This includes both the run capacitor and the start relay. The capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your ...

$18.84

Light Switch

This part turns on the light when the door is opened.

$15.21

Water Fill Cup and Bearing

$17.83

Fan Blade

Used with Evaporator Fan Motors.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 603 of 624 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

The compressor would not run.

  • Customer: Gilbert from Clinton MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 212 of 239 people found this instruction helpful
I removed the screws in the lower back panel where the compressor is located. Then I unplugged the capacitor and plugged the new one in. I then checked to see if the compressor would start. It wouldn't so I replaced the overload relay with capacitor and that fixed the problem. The capacitor just plugs into the relay then plugs into the compressor. There are ... read more

Freezer is cold, Refridgerator is not as cold as it should be

  • Customer: Russell from Hardinsburg KY
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 220 of 267 people found this instruction helpful
Having seen this problem before in other equipment so I had an idea where to look. Problem: the automatic defrost function was not operating. Looking through openings in the back panel of the freezer compartment, you could see the evaporator coils and fins were a solid chuck of ice. There are three logical components to check. Heater element, thermostat ... read more