JCB2059GES (PJCB2059GS1) Jenn-Air Refrigerator - Instructions

took off the ice maker, unscrewed the body, replace icemaker shut-off arm, water fill cup & bearing, reconnected the unit & have ice now, Thank you PartSelect

Simply remove the filter and insert the bypass cap in its place. Cap turned a little hard but if your careful everything goes together easily.

easy enough, removed 3 screws, unplugged wiring harness, put new unit on work bench, put old wire harness on new unit, put old motor cover on new unit,(the only trouble i had was figuring out how to swap the light blue plastic piece for the white plastic piece, i just put a screwdriver underneath and applied pressure) plugged harness back into freezer, turned water back on and waited... 2 hours later heard beautiful ice cubes dropping into tray :)

So simple I couldn't believe it! Twist out the old filter then twist in the new! Easy Peasy!

The ice maker was easy but the older Maytag inlet valves are rigid plastic line- make sure that line is properly connected to back of fridge- the 1st night the water leaked down back of freeze- thus no ice in ice maker tray ----but the bottom of freezer was full of frozen water--- took ice maker off and realigned inlet pipe- once that was done- no more problems- ( did also have to take hair dryer and remove all ice build up in bottom of freezer --- remember to check that rigid line as it can become detached while changing out ice maker assembly- thx Greg

The existing instructions are very good and need no further clarification.

Just followed directions.Which were clear as could be. I think it took longer to clear the freezer, than to replace the ice maker. Thanks so much.

I opened the cover to the filter and screwed the filter counter clock wise until it came loose then removed the old filter and put the new one in. It was real easy.

Unplugged refrigerator and truned off water supply. I then removed old ice maker by first removing screw holding mounting bracket with 1/4 inch nut driver. Then I carefully pulled up and out on the ice maker to remove it from mounting brackets on the side of unit. Once free, I was able to access the wiring harness in the back and remove it from the unit by compressing the clips and gently pulling with an even pressure. Now that the old ice maker was detached I took it to my counter and removed the on/off switch rocker bar and wiring harness. I attached these two pieces to the new ice maker. I then plugged the wiring harness back into unit and lined up the mounting brackets on the side wall and did a reverse tilt to downward pressure onto brackets until they clicked in securely. The last step was to screw in the mounting bracket with nut driver. Turned on water line and plugged machine back in. It took about an hour and a half before it produced its first harvest of ice, but has been working like a charm since.

Watch the video on the sight and that was almost all I really needed. The only thing I would add is that it took me some time to get the drawer freezer door off. Lift the front straight up. Don't pull the door slides out.

It was very easy, just unscrew old filter and screw in the new filter. Reset the warning light, and done. Ralph Mason, 403 Sundance Lane, Georgetown, TX 78633

Was very happy with the experience of using your company. The man on the phone was helpful. The icemaker shipping was only about $7 and got here in a couple of days. I liked the video, and then including a link to the video with the on-line confirmation. Was not quite sure it was the icemaker or the metering valve on the back, as the latter would make a little grinding noise, but the symptoms matched the dumping of water into the bin. After replacing, everything is working well. The only difficulty was the wire harness plugs into the other side of the back of the box than in the video and I found it a little difficult to route the wires correctly as they seemed too short. But a little trial and error solved that. My model is freezer on the bottom and I didn't notice that the little detachable funnel wasn't quite seated and it was necessary to reinstall, making sure the funnel stayed in place correctly. That was my own error. My overall experience was excellent and I would not hesitate to recommend PartSelect to anyone with an icemaker problem. I'm only sorry I lived with a recalcitrant ice maker for a couple of years before finally acting on it. I am glad I found your website! Lee in Texas

Thanks to some reviews we found online about replacing gaskets, ours went very smoothly. One person said to soak the gasket in hot water, which we did til it was very soft. Installed like a breeze. Then, the same person said to tape the door closed after installation, we did that too. The gasket looks like it was professionally installed and we have never done it before. Thanks!

Removed icemaking mechanism replaced with new. Works better than ever

I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!