Models > JBS55DM2WW > Instructions

JBS55DM2WW General Electric Range - Instructions

All installation instructions for JBS55DM2WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JBS55DM2WW
166-180 of 227
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Element turned white and broke

  • Customer: Jennifer from Sanford FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Ordered the new element (and two new racks since mine were over 10 years old) on Friday afternoon. Parts arrived Saturday! I was so pleased. All I had to do was unplug the stove, remove two nuts, pull out the old element, push the new prongs onto the clips, and replace the two nuts. Done. Works great and all parts were a perfect fit!! I will be ordering again when I replace the burners and drip pans!

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Hard to move drawer in and out because the rear drawer supports broke off.

  • Customer: Steven from Lansdale PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

dropped & broke the oven light bulb cover

  • Customer: joseph from san jose CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
popped the new one on!

Baking element burned out

  • Customer: Jon from Bondurant IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled oven out removed six screws from the plate covering the wires pulled wires from end of element.Removed the two screws that hold element inside the oven. Removed broken element and installed new element.

Lower element wasn't getting hot.

  • Customer: Sherman from Seguin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed four screws from rear panel and two screws from element. Then removed the two wires from the element. Replaced element and the two wires along with thesix screws. It a grand total of five minuets on thanksgiving morning. Just in time to finish the rest of the meal.

Wall oven: light flickered or did not work in a loose poreclain socket.

  • Customer: Robert from Owings Mills MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off power at the panel to the electric oven. Removed 2 phillips screws holding bulb unit in place in the top of teh oven chamber. One wire was so frayed it came out of the push on connector. Stripped off insulation and reinstalled onto the connector, using pliers to snug the wires down. Installed the new porcelain socket from Parts Select, replaced the unit in the top of the oven unit. Installed a new bulb, then snapped the new glass housing into place with the existing retaining wire clip. Presto: works like it's brand new. Thanks to Parts Select for the right parts, and for such quick delivery. I will use them again!

lower oven heating element out

  • Customer: Mark from Memphis TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Hardest part was dragging oven away from wall and cleaning floor. Unscrewed 2 oven screws holding heating element in. Unscrewed 4 back screws holding cover panel on back. Unclipped connections. Heating element slid right out. Put new one in, reclip wires and put screws back. Simple. Usually I'm 10 thumbs so this simple repair was mentally uplifting.

Bottom element burned out

  • Customer: Richard from Buchanan MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Repair was very easy. Removed two nuts with nut driver and unhooked old element and new element slipped right on terminals. Replace nuts with driver and we were ready to go.

shattered front glass

  • Customer: louis from pacific MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Only had to take out 2 screws and 3 bolts, the new glass slid right in, there was alittle trouble lining up the bolt holes when puttung back together but that wasn't even realy that bad.

oven would not heat up

  • Customer: Alan from Shamokin PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took off old heating element and replaced with new heating element. no appliance store in my area had the replacement element. googled heating element and found the site and ordered part. had part within 5 days.

Oven light wire broken, damaged socket

  • Customer: Patricia from Brandenburg KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

bake element broken in two parts

  • Customer: patrick from pawnee IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
its easy take the plate off pull it out disconnect the leads i used locking pliers to hold the leads from going up into the insulation until i installed the element 10 min easy .

Burner not operational.

  • Customer: Gerald from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy
All Instructions for the JBS55DM2WW
166-180 of 227