JBP64BB4WH General Electric Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Heating element
The heating element in my electric oven cracked, I had something boil over onto the element, cracking it to the point of it sparking. First time I had ever seen this before. The appliance repair shop was going to charge me a small fortune to fix this so I ordered the part online, which it was 10.00 cheaper from here than from any other site. It got to me quickly and took me less than 15 minutes to repair and everything works great. All I had to do was unbolt 2 screws with a ratchet, unplug the element, plug in the new one, and bolt it back up and I was done!
Parts Used:
-
Kathy from Crosby, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
9 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior light needed replaced
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Parts Used:
-
Leo from TWIN FALLS, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
14 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven on range did not work properly
My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.
Parts Used:
-
Dinah from Juneau, AK
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Socket set
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven door insulated glass broken
1) Remove the door from the oven.
2) Remove two screws from top oven face of door.
3) Flip door over
4) Remove 3 screws from bottom edge of door
5) Lift front door half from inside door half.
5) Remove 5 screws retaining the glass
6) Replace glass assembly and re-assemble door.
2) Remove two screws from top oven face of door.
3) Flip door over
4) Remove 3 screws from bottom edge of door
5) Lift front door half from inside door half.
5) Remove 5 screws retaining the glass
6) Replace glass assembly and re-assemble door.
Parts Used:
-
Wolcott from Pennington, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Liight Socket
Removed the broken socket, and replaced with new one.
Parts Used:
-
Rchard from Derry, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
14 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven not holding a consistant temperature. Found the replacement part easily on you website.Thanks to your photo.
First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.
Parts Used:
-
Cindy from Murrells Inlet, SC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
10 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing Oven Racks
When we moved into our new home I discovered that the oven that came with the home did not have any racks in it. I ordered these racks because they said they were compatible with Hotpoint ovens. However, when the racks arrived they were just a tad too wide to easily slide in the oven. With a bit of force my husband was able to shove the racks in. Luckily I don't cook enough to care if they are moved again because I don't think they'll come out easily.
Parts Used:
-
Micala from Tucson, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
back burner not getting hot
unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$
Parts Used:
-
William from Shenandoah, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element burned out
TURNED OFF CIRCUIT BREAKER FIRST. Pulled Stove from wall, Removed 5 screws to remove back plate. Unplugged 2 spade electrical connections. Unpluged temp. sensor plug. Opened oven door and removed 2 screws holding element to top of oven. removed screw holding temp probe to element. Installed the elment in the reverse order starting with the temp probe. when finished with install, I tested the unit before covering the back. I used a oven temp tester to make sure that when the element went out that the temp probe was not damaged. Everything checked out fine and I finished installing the back cover and putting stove in place. Cleaned up area and JOB DONE.
Parts Used:
-
Larry from Keystone Heights, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace stove top burners (3 total)
Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.
Parts Used:
-
Thomas from Bonifay, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had to replace the broiler element
Removed the old element with a nut diver and put the new one in. Very simple instalation.
Amazingly the part arrived in just two days...
My T-Bone steaks are cooked just the way I like them again.
MikeS, Birdsboro, PA
Amazingly the part arrived in just two days...
My T-Bone steaks are cooked just the way I like them again.
MikeS, Birdsboro, PA
Parts Used:
-
Mike from Birdsboro, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower Element Open
Removed the 2 screws on plate. Pulled wires forward. Simply detached slide on connecters and inserted new element. Pushed back and installed plate. Dont forget to unplug the 220 volt. Though open can ground wires.
Parts Used:
-
ROBERT from TEGA CAY, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heat sensor malfunction
Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...
Parts Used:
-
Diane from BUTLER, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
switch went to high setting no matter what the setting was
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..
Parts Used:
-
Frank from Glen Cove, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
10 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element wouldn't heat
Removed the two screws that hold the element in place, then I disconnected the two wires and pulled the element out. I ordered the part and received it within two days. It was very easy to install. My oven was tunning in less than half an hour.
Parts Used:
-
Leanne from Huntington, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!