JBP24BB4WH General Electric Range - Instructions

My husband actually did the replacement but I did all the research online to find the right part. I wasn't sure we'd find it for our old stove but luckily we did and it works fine. Thanks for the super fast service!

My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.

Took off the ring burners and the old drip pans . installed the new drip pans and the old burners took less than 3 minutes...so easy

replaced lights in refrigirator and freezer

After removing power from the range, I pulled the unit out for better access to the rear. I carefully pulled all four knobs off the front of the control panel. Next, using a short phillips screwdriver, I removed two screws from the front bottom of the control panel. On the rear of the control panel, there are four screws to loosen, now the whole panel is free to remove toward the front of the unit. The burner switches are held onto the panel with two screws that are located on the front under where the knob had been. The wires are all connected to the switch with crimp type connectors. These are on tight, but can be removed carefully with pliers. Before doing so, I took a picture on my phone to ensure I replaced the wires in the correct order. Everything goes back together in reverse order. This is a good time to clean behind and under the whole stove. The whole process took around 20 minutes.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

1.) I removed the old oven door gasket by taking out the ends of the gasket out of the bottom of the oven door first.
2.) Pry up on each one of the retainer clips, they easily pop out of their slots.
3.) Work your way around the oven door gasket.
4.) If any remain stuck you can just wiggle the clip around and it should pop out of each hole. If need be you could use pliers, but I did not need to.
5.) Take your new gasket, it should already have new clips, so you can throw away the old ones.
6.) Work your way around the oven door making sure the clips are nicely seated.
7.) Finish off by inserting the ends back into the 2 holes on each side of the bottom of the oven door, I just used a small spoon to make sure the tops were nicely placed in.
8.) If your gasket needs to compress, you can close the oven door and lock it that should hold it in place and compress it.
9.) All done!

Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!

I got tired of trying to find the right parts in the stores and decided to order them. Finally I have the drip pans that fit my range!

Nothing to it. Took off the old ones and put on the new! Tada - new stove!!

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

Fortunately there was no repair needed, just a replacement of old parts, but I was very pleased with the speed of delivery and the quality of the parts. I'm a happy customer.

First , I have been working on electrical equipment for many years....and I forgot to un plug the unit from the wall. I assumed that if the oven was turned off I could remove the element, WRONG. One of the leads from the cord is wired directly to one lead of the element. When I tried to remove the element it shorted out against the wall of the oven. Then I turned the breaker off, unplugged the stove and finished the repair in about 10 minutes. Always unplug it first!.

Received part very quickly, easy to install, just give yourself enough wire on terminals when you pull them out, I let mine slip into holes they come out of and had to fish it out. EASY job.

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !