Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JB940TD1WW

JB940TD1WW General Electric Range - Overview

Get Parts and Repair Help for JB940TD1WW

If you know the range repair part you need, you can browse the list of all parts on the JB940TD1WW, or you can search by name or part description. You can also find your part by where it is located on the JB940TD1WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for JB940TD1WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$10.48

Temperature Sensor

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is having difficulty achieving warmer temperatures and/or keeping warmer temperatures up, you may want to test your temperature sensor. Before you make this repair remember to unplug your range from the power source, and turn off the gas shut off valve.

$5.30

Rear Drawer Support

This rear drawer support comes with the installation screw. ***NOTE: There has been a factory design change and you must change both rear supports from side to rear.

$129.47

Dual Haliant Element with Limiter - 9" - 2500W

This is a large dual haliant element with a limiter or sensor for glass cooktops and freestanding ranges. It is a 2500-watt part. The inner diameter measures 9 inches, while the outer diameter measures 10 inches. If there is no heat generated from your element, you may need to replace this part. You may also need to check your socket or infinite switch. It is located under the glass cooktop of your appliance. Be sure to unplug or cut the circuit breaker to your appliance before starting this repair. Before replacing this part, be sure your appliance is getting enough power. If it is receiving less than the required 220 volts of alternating current, the surface element will not work.

$7.36

Foot - Leveller

Sold individually.

$7.03

Oven Light Socket - With Push In Receptacle

$14.00

Door Bottom Channel Trim - White

$2.06

Screw

This screw is sold individually.

$3.29

Screw

Sold Individually.

$95.58

Large Haliant Burner with Limiter - 8"

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Large burner on dual element burned out

  • Customer: Scot from Oakland, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 85 of 98 people found this instruction helpful
This was really easy, and pretty with no problems or issues It took me longer to write this than to do the actual installation. I used a digital camera to help me remember where things were, but a pen/paper works fine. Here's what I did:

1. Turn off the breaker for the cooktop.

2. Remove (2) 1/4" hex screws directly under cooktop. You m... read more

Oven would go in to a F2 Error

  • Customer: Peter from stamford, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 76 of 100 people found this instruction helpful
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function. read more

Large burner would not get hot

  • Customer: Kevin from Leominster, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 59 of 74 people found this instruction helpful
Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple! read more