Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JB700CD2CC

JB700CD2CC General Electric Range - Overview

Get Parts and Repair Help for JB700CD2CC

If you know the range repair part you need, you can browse the list of all parts on the JB700CD2CC, or you can search by name or part description. You can also find your part by where it is located on the JB700CD2CC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for JB700CD2CC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the JB700CD2CC

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.80

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

Order within the next 6 hrs and your part ships today!
$56.23

Bake Element - Push On Terminals - 240V

The bake element in your oven provides the cooking heat. This part can be found at the bottom of your oven, and attaches to the power source on the back wall. It has two terminals that fit into the power source receptacle. This part is made of metal, and is approximately 20 inches in length and 18 inches in width. This product is sold individually. Many of our customers have rated this repair as easy. To complete this repair, simply lift the old element up and out of your oven, and replace it with the new one. Be sure to disconnect power from the oven before you begin this repair.

Order within the next 6 hrs and your part ships today!
$10.83

Temperature Sensor

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to meas...

Order within the next 6 hrs and your part ships today!
$5.31

Rear Drawer Support

This rear drawer support comes with the installation screw. ***NOTE: There has been a factory design change and you must change both rear supports from side to rear.

Order within the next 6 hrs and your part ships today!
$57.46

Broil Element

This broil element is found on the upper part of the oven cavity.

Order within the next 6 hrs and your part ships today!
$32.86

Oven Rack

Sold individually.

Order within the next 6 hrs and your part ships today!
$27.10

Surface Burner Switch - 6" - 1560W

This switch controls the small burner on a range/stove top.

Order within the next 6 hrs and your part ships today!
$7.19

Foot - Leveller

Sold individually.

Order within the next 6 hrs and your part ships today!
$7.21

Oven Light Socket - With Push In Receptacle

Order within the next 6 hrs and your part ships today!
$2.12

Screw

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven element burned itself up

  • Customer: Dennis from Bondville, VT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 225 of 242 people found this instruction helpful
Turned off circuit breaker to range.
Removed the 2 oven racks. Removed two screws in back of oven compartment. Pulled element forward and the terminal connections get exposed.
The right terminal clip disconnected by itself and the wire went back into the stove and could not be retrieved.
Removed range draw under the oven and pulled entire rang... read more

The baking assembly in the oven burst into flames one day, then broke apart.

  • Customer: Theresa from Sherman, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 122 of 126 people found this instruction helpful
After the element cooled down, I pulled the racks out of the oven, turned off the oven at the breaker box, then, using a nut driver, loosened the screws that held the baking assembly in the back of the oven, and pulled the connecting wires off. I bent the wires to make sure they would stay out, because if they get back in the insulation, they are hard to fin... read more

Oven would go in to a F2 Error

  • Customer: Peter from stamford, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 76 of 100 people found this instruction helpful
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function. read more