Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JB552GK-2

JB552GK-2 General Electric Range - Overview

Get Parts and Repair Help for JB552GK-2

If you know the range repair part you need, you can browse the list of all parts on the JB552GK-2, or you can search by name or part description. You can also find your part by where it is located on the JB552GK-2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the JB552GK-2

[Viewing 4 of 4]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$18.47

Broiler Pan - Large

This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain....

$77.92

Oven Sensor

This sensor offers 16 ohms of resistance at room temperature, though the resistance increases as the temperature increases.

$35.39

Fluorescent Lamp/Bulb

$48.11

Power Terminal Block Kit

This kit comes with the terminal block, nuts and wires.

$5.56

Leveling Leg

$139.98

Element Disc

This is an element disk but may also be known as a surface element and it is a part for your range. The function of this disk is to give heat to the cooking area on top of the range. This disk is for your seven-inch element, and is off-black in color. The most common reason for needing to replace this part is if your element is no longer heating, or is taking too long to heat. To make this repair you will need a screwdriver set, a nut driver, and a pair of needle-nose pliers.

$58.14

Bake Element

This bake element is found on the bottom of the oven. NOTE: Screws are NOT included.

$139.98

"DISC ELE-6"" "

$92.85

Door Latch Solenoid

$1.58

CLIP TRIM

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Large burner very slow heating

  • Customer: Drusilla from Bloomfield, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 17 people found this instruction helpful
Downdraft stove is over 20 years old, but everything else works fine and it would be a real pain to replace it.

This quick-heat back burner is part of a two burner plug- in unit which takes up half of the top of the stove.

I removed the top from the rest of the unit easily removing five screws. Because of the age and long use it was to... read more

oven would not come up to temperature

  • Customer: Clarence from Norwich, NY
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 13 of 16 people found this instruction helpful
Removed sensor from back wall of oven by removing 2 screws from flange. I could not pull the wire-nut connections out through the small hole and thought I would have to pull the whole oven out of the wall to acess the connections from the back so instead I clipped the wires close to the old sensor and connected the new sensor with the small wire nuts provide... read more

oven temperature too low

  • Customer: Ryan from Henderson, NV
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 11 of 12 people found this instruction helpful
After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature. read more