Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JAV4200AWA

JAV4200AWA Maytag Washer - Overview

Get Parts and Repair Help for JAV4200AWA

If you know the washer repair part you need, you can browse the list of all parts on the JAV4200AWA, or you can search by name or part description. You can also find your part by where it is located on the JAV4200AWA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for JAV4200AWA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$56.03

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - t...

Order within the next 8 hrs and your part ships today!
$98.98

Hub and Seal Kit

This kit prevents water from leaking around the drive shaft and down to the bottom of the tub.

Order within the next 8 hrs and your part ships today!
$34.73

Lower Bearing Assembly

Order within the next 8 hrs and your part ships today!
$48.23

Agitator Base

Base only. Top agitator sold separately.

Order within the next 8 hrs and your part ships today!
$38.58

Lid Switch Kit

This kit includes the bracket, actuator, switch, screws and wire harness.

Order within the next 8 hrs and your part ships today!
$13.74

Flume Hose Kit

Order within the next 8 hrs and your part ships today!
$74.75

Agitator Top

This part fits on top of the agitator base.

Order within the next 8 hrs and your part ships today!
$381.95

Transmission and Seal Kit

Order within the next 8 hrs and your part ships today!

Plastic Outer Tub

$25.96

Tub Seal Kit with Brass Ring

This seal helps prevent any leaking around the transmission of washing machines.

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washing machine was making alot of noise

  • Customer: David from Boca Raton, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 520 of 525 people found this instruction helpful
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again. read more

One of the plastic hinge pins brroke

  • Customer: Allen from North Little Rock, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 480 of 477 people found this instruction helpful
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. read more

Washer jumping in spin cycle (white flakes under the washer)

  • Customer: David from Butler, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 229 of 238 people found this instruction helpful
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of... read more