J760X30C General Electric Range - Instructions

Repair was simple (just lift off the old and put on the new). What was pleasantly surprising was how quickly I received the parts (amazing)!

Lastly, I've been looking for the correct parts/sizes in stores for years (yes, I should have tried this sooner). I was delighted to finally find a place that actually had the correct parts.

Received the Drip bowls and Rings very quickly. Opened the box and then cut open the plastic wrap that the individual rings and drip bowls were in. Lifted the burner on the stove top, took out the old ring and drip bowl. Installed the shiny new drip bowl and ring, then lowered the stove top element back into place. I was able to replace all 4 of them within 5 minutes. Made the 30 year old stove look brand new.Thank you for perfect fit parts and fast delivery.

In order to determine what was wrong with the oven I used a voltage meter to determine if power was coming to the element in the first place. Be careful to set your meter at least 500 ACV, as the oven is operating at 240V. Remove the two screws that hold the element in place and carefully pull it out of the side of the oven. Turn on the bake element in the upper oven and place your test leads to either side of the connection leads. If you get a reading of 240Volts plus or minus you will know for sure the element is bad.
Turn off the oven, or even better turn off the circuit breaker to your stove.
There are two leads to the element that are held in place by self taping screws. If you have the same luck I have they will be corroded together. Carefully use long nose pliers to hold steady while gently applying pressure. If necessary use liquid wrench. When separated put together in the reverse order as how you took it apart.

So this ancient stove we inherited when we bought our house had the drip bowls wrapped in tin foil. We've searched EVERY (not joking) store in our area for drip bowls that would fit it, but apparently Hotpoint wanted to make sure you could never do this - well, at least not easily. No one, not one store carries drip bowls to fit it. I finally searched online and partselect.com came up first on the list. I was amazed they had the right part! Better yet, ordering was beyond easy, and they came super quick. Popped in the parts in less than 2 minutes, and we're good to go - makes this old stove look new! (well, if this was the 80's, lol) When I clicked on the part it said which stoves it would fit, which was also very helpful. Thank goodness for Part Select! Otherwise we would've had to rewrap those disgusting old bowls... I'd recommend this site in a heartbeat!

Replaced all the ordered parts, and straightened a bent "rest piece" (one of three) on the element os the large burner, which made it rest perfectly on the new Trim Ring. It doesn't easily fall down into the bowl now while I am using the burner. The new Bowls look so nice, and the stove looks nearly new!

I now know where to go for help when I need to repair appliances. You seem to have everything that could possibly be needed. Thank you!

Turned off the electricity to the ovens. Unscrewed the two screws holding the old bake element. Removed the old one by disconnecting the two wires and replaced the new element in it's place.

Simply took the replacement part ( PS244040, GE WB30X341) and did the quick direct swap using all the new pieces in the burner kit. UNPLUG the stove. Undo the titl arm screw, remove the plastic wire isolation block (2 spring clips), unscrew the 3 wires to the elements, screw the 3 wires to the new element, put in new bakelite wire isolation block with spring clips to keep the wires seperated, mount and titghten the tilt arm screw. Make sure the burner sits even and flat in the stove top. Plug the stove back in and test.

I just replaced them.

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

I had purchased a partselect heating element for my larger lower oven previously so I knew what to expect on replacement.

I shut off the power to the stove from the electrical box. Next I removed both the cooking racks from the oven. Then the side removable panels and bottom as this is a P7 removeable panel oven. This gave ne easy access to the nuts/screws holding the element in place. Once the screws were removed I pulled out the element and disconnected the leads. I replaced the new piece reversing the process.

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

Removed the burned-out element with appropriate tools; installed new element with same tools.

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.

First I made sure the electricity was off. Then, I flipped the burner up, and loosened the screwon the hinge. This allowed the burner to extend onto the cook surface. After loosening the clips holding the ceramic insulator together, the wires to the element were exposed. The wires were then transferred to the new burner element from their corresponding position on the old one. The new ceramic insulator was affixed over the wire with clips, and the hinge reattached. The chrome ring was worked over the burner, and the burner reseated in its proper cook poistion. Testing confirmed the burner to now work as new.

the replacement items fit really good. It was a matter of remove and replace,