Models
>
J66RP1BG
J66RP1BG General Electric Cooktop - Overview
Sections of the J66RP1BG
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Infinite Switch Burner Knob
PartSelect #: PS249164
Manufacturer #: WB3X800
Sold Individually. This knob accepts a double-flat shaft.
No Longer Available
Switch Seal
PartSelect #: PS243590
Manufacturer #: WB2X9504
This part goes between the infinite switch (under the cooktop) and the knob.
$32.19
In Stock
Razor Scraper
PartSelect #: PS311651
Manufacturer #: WX10X302
This is sometimes used to clean glass stovetops.
$10.43
In Stock
SURFACE DUAL RADIANT ELEMENT 9" KIT"
PartSelect #: PS16225972
Manufacturer #: WB30X38934
This dual element can be changed to be used as either a small or large burner. It comes with the element limit switch.
$262.51
On Order
Cerama Bright Cooktop Cleaner
PartSelect #: PS783497
Manufacturer #: PM10X310
This is a 28 oz bottle of Cooktop Cleaner.
$18.28
In Stock
SURFACE RADIANT ELEMENT 8" KIT"
PartSelect #: PS16225968
Manufacturer #: WB30X38926
No Longer Available
Questions And Answers for J66RP1BG
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the J66RP1BG
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cooktop Burner was always on High no matter what the setting on the Control
1) Turn Power off at Circuit Breaker
2) Lift Cooktop out of counter top.
3) Remove all dials from controls by pulling straight up.
4) Remover glass plate which covers burners by removing
screws along outer edge.
5) Remove the two top screws from the control to be
replaced (this holds the infinite contr ... Read more ol to bracket)
6) Remove one wire at a time from the old control and
plug on the new one in correct orientation.
7) Reverse above order to reassemble.
(Note: Not all infinite controls are same PN when
ordering, the drawingings are deceiving that they are)
2) Lift Cooktop out of counter top.
3) Remove all dials from controls by pulling straight up.
4) Remover glass plate which covers burners by removing
screws along outer edge.
5) Remove the two top screws from the control to be
replaced (this holds the infinite contr ... Read more ol to bracket)
6) Remove one wire at a time from the old control and
plug on the new one in correct orientation.
7) Reverse above order to reassemble.
(Note: Not all infinite controls are same PN when
ordering, the drawingings are deceiving that they are)
Read less
Parts Used:
-
Raymond from Salt Point, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
32 of 41 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Flat surface stovetop element was burned out
1. Removed brackets holding the cooktop in place.
2. Removed the cooktop.
3. Removed the screws holding the housing for the elements.
4. Removed bad element.
5 Connected new element.
6. Reassemble
2. Removed the cooktop.
3. Removed the screws holding the housing for the elements.
4. Removed bad element.
5 Connected new element.
6. Reassemble
Parts Used:
-
Leslie from Meridian, MS
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
16 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The shaft on the selector switch broke.
You have to replace the switch if the shaft breaks (I think we hit it with a pot). This is a flat glass cook top. Turn off the power at the breaker box. I took the drawers out below the cook top and loosened the bracket holding the electrical conduit. That allowed me to push up the cook top from below. There is some adhesive but nothing h
... Read more
old it except its own weight and the adhesive. You do not need to disconnect the conduit. Remove all of the knobs. Remove all of the Phillips screws around the upper perimeter. Do not remove any of the hex screws yet. When all of the screws are removed, lift the glass cook top off of the metal "guts." At this point there will only be adhesive holding it on. Now remove two hex screws at each end of the control strip. Remove the two Phillips screws from the subject switch. Lift up the the control strip, disconnect the electric leads to the switch, reconnect the leads to the new switch, and then re-attach the new switch to the control strip with the two Phillips screws. Then go backwards. Replace the control strip and secure with the two hex screws at each end. Before replacing the cook top, check the burners. They rest on posts with small springs designed to keep them flush with the glass cook top. Make sure that all of the burners are properly aligned on their posts and springs. Replace the cook top and re-attach with all of the Phillips screws. Return the cook top to its resting place making sure the adhesive strips are correctly placed around the perimeter. Replace the bracket on the conduit. Put the knobs back on. Flip the breaker back on and start cooking.
Read less
Parts Used:
-
David from Porter Ranch, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
12 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!