Models
>
J351*01
J351*01 General Electric Range - Overview
Sections of the J351*01
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
INFINITE HEAT SWITCH KIT
PartSelect #: PS16216966
Manufacturer #: WB21X36771
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
$51.36
In Stock
8 Inch Surface Burner
PartSelect #: PS244046
Manufacturer #: WB30X348
This surface element kit includes an 8 inch element, two wire, 2350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
$90.22
In Stock
Tilt Lock Hinge Mounted Surface Burner Kit - 6"
PartSelect #: PS244042
Manufacturer #: WB30X342
This tilt lock hinge mounted surface element kit includes a 6 inch, three wire, 1350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
$49.45
In Stock
Oven Sensor
PartSelect #: PS235718
Manufacturer #: WB21X158
This sensor offers 16 ohms of resistance at room temperature, though the resistance increases as the temperature increases.
No Longer Available
Timer Kit
PartSelect #: PS233998
Manufacturer #: WB19X10008
This kit replaces some mechanical clocks. ***Please NOTE: The wiring of this part may be difficult and it is best to have it installed by appliance repair person.
$383.97
In Stock
Questions And Answers for J351*01
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the J351*01
[Viewing 2 of 2]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Large burner would operate on high setting only.
1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
Parts Used:
-
Ernest from Bellevue, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Socket set
20 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven temperature too low
After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature.
Parts Used:
-
Ryan from Henderson, NV
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
16 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not come up to temperature
Removed sensor from back wall of oven by removing 2 screws from flange. I could not pull the wire-nut connections out through the small hole and thought I would have to pull the whole oven out of the wall to acess the connections from the back so instead I clipped the wires close to the old sensor and connected the new sensor with the sma
... Read more
ll wire nuts provided, then enlarged the hole in the oven wall, being careful not to pinch the wires then pushed the wire nuts and extra wire back through the hole and put the screws back in the flange.
Read less
Parts Used:
-
Clarence from Norwich, NY
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!