Quick Question!

Have you ever purchased from PartSelect.com before?

Models > J2S968TEK2WW

J2S968TEK2WW General Electric Range - Overview

Get Parts and Repair Help for J2S968TEK2WW

If you know the range repair part you need, you can browse the list of all parts on the J2S968TEK2WW, or you can search by name or part description. You can also find your part by where it is located on the J2S968TEK2WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for J2S968TEK2WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.06

Grate Foot

The grate foot pad attaches to the bottom of the burner grate to prevent the cooktop from being scratched. It protects the stove top by cushioning the grate on your gas range. Over...

$15.47

Oven Sensor

The function of the oven sensor is to detect the temperature within the oven cavity. If you notice that the oven is too hot or too cold, or it is not heating evenly, you may need to replace the oven sensor. The oven sensor is typically located in the back of the oven so you will most likely need to pull your oven out to access it. Many of our customers have rated this repair as easy. You will need a Phillips screwdriver to complete this repair. Be sure to disconnect the power source and shut off the gas valve before doing this repair.

$5.30

Rear Drawer Support

This rear drawer support comes with the installation screw. ***NOTE: There has been a factory design change and you must change both rear supports from side to rear.

$18.43

Broiler Pan - Large

This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures 15-1/2 inches wide by 13 inches deep and the pan is about 17 inches wide by 13 inches deep. No tools are required to replace this item, simply pull out the lower drawer of your range, pull down the front of the drawer, slide the pan out and slide the new one into place. This is a genuine part sourced right from the manufacturer.

$40.16

WINDOW PACK ASM

$7.36

Foot - Leveller

Sold individually.

$2.06

Screw

This screw is sold individually.

$1.62

Screws - Package of 12

$13.58

Halogen Light Bulb - 50W

This light bulb is used in the interior oven.

$3.71

Front Drawer Support

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

terminal block melted

  • Customer: jonathan from willow springs, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 40 of 47 people found this instruction helpful
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal ... read more

Oven was not coming up to temperature

  • Customer: Sean from Highlands Ranch, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 36 of 41 people found this instruction helpful
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very e... read more

Plastic drawer support snapped off

  • Customer: Jeff Troiano from Sayville, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 24 of 24 people found this instruction helpful
The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online. read more