Quick Question!

Have you ever purchased from PartSelect.com before?

Models > INT21D8 (5A77A)

INT21D8 (5A77A) Admiral Refrigerator - Overview

Get Parts and Repair Help for INT21D8

If you know the refrigerator repair part you need, you can browse the list of all parts on the INT21D8, or you can search by name or part description. You can also find your part by where it is located on the INT21D8 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for INT21D8 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling the warm refrigerant before it enters the evaporator. When your fan or fan motor is not working your refrigerator will not cool properly. This is a 2-Watt, 115 Volt motor that rotates the fan in a counter clockwise direction. This kit includes the hardware needed for installation, and a set of instructions. Before you begin any repair work make sure to unplug your appliance.

$39.04

Single Outlet Water Valve Kit

This part is a solenoid-operated switch located at the bottom of the refrigerator. When the water inlet valve is turned on, water is released from the supply line through the water...

$3.02

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.98

Screw

Sold individually.

$4.48

Inlet Hose Washer

This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal in the appliance. If your gasket gets dry and brittle over time it will start to crack and will lose its function. In this case, it is important to replace it. Refer to the manual provided by the manufacturer for further installation instructions and accurate guidance. As a safety precaution, remember to unplug your washer from the power source before beginning.

$5.58

Compression Nut

The compression nut is used as a connection between the water supply line and other components in your refrigerator such as your ice maker and your water dispenser. Tools required ...

$70.21

Evaporator Fan Motor - 115V 60Hz - Blade NOT Included

This is an evaporator fan motor for a refrigerator. The fan motor circulates air through the refrigerator to the fresh food compartment for efficient cooling. It is just over three inches long. It is made of both metal and plastic, and is made up of black, white, and metallic pieces. Disconnect power from your refrigerator before starting the repair because you will be working near electrical circuits. This is an authentic replacement part that is sourced directly from the original manufacturer. It is important to note that the blade is sold separately and is not included with the evaporator fan motor.

$5.00

Plastic Tubing

This part supplies water to refrigerator components that require water, such as the ice maker and water dispenser. If you notice a leak coming from your refrigerator, the plastic t...

$40.41

Defrost Thermostat - With Wire and Clip

This refrigerator defrost thermostat will cut out at 80 degrees Fahrenheit and kick back when the temperature drops to 15 degrees Fahrenheit.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 138 of 149 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

no water getting to ice maker

  • Customer: Kevin from Boston, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 60 of 69 people found this instruction helpful
The ice maker had been slowly dying and one day just stopped making ice. No water was getting to the trays.

I read that this could be caused by a failure of the valve, even though the continuity test indicated that the solenoid was okay.

I ordered the part Friday afternoon. It was delivered Saturday. I did the repair in 10 minutes.
read more

noisy fan motor

  • Customer: robert from nashotah, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 26 of 31 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more