Quick Question!

Have you ever purchased from PartSelect.com before?

Models > IMS106

IMS106 (BY09A) Maytag Ice Maker - Overview

Get Parts and Repair Help for IMS106

If you know the ice maker repair part you need, you can browse the list of all parts on the IMS106, or you can search by name or part description. You can also find your part by where it is located on the IMS106 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for IMS106 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term

[Viewing 1 of 1]

Complete Ice Maker Kit

This part number matches the current model number "IMS106".

This heat release ice maker kit comes with a water inlet valve, an ice bin, the icemaker, and all the related hardware. This ice maker kit forms crescent shaped ice cubes, and is intended for use with refrigerators that have been manufactured since 1989/1990.

Sections of the IMS106

[Viewing 1 of 1]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$97.39

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

Order within the next 12 hrs and your part ships today!

Sensor Shut-Off Arm

This part signals the icemaker to stop making ice once the bin has reached a desired amount.

Icemaker Wire Harness

TUBE, FILL

CLAMP- TUB

CEMENT, ALUMILASTIC (4 OZ.)

SCREW, 10-32 X 43/64

Plastic Tubing

1/4" Plastic tubing, 8 1/2 feet long.

$17.01

DUCT-AIR

SLEEVE, SENSOR ARM

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 662 of 698 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 243 of 316 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 90 of 106 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more