Models > IMS105

IMS105 Jenn-Air Refrigerator - Overview

Get Parts and Repair Help for IMS105

If you know the refrigerator repair part you need, you can browse the list of all parts on the IMS105, or you can search by name or part description. You can also find your part by where it is located on the IMS105 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for IMS105 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term [Viewing 1 of 1]

Complete Ice Maker Kit

This part number matches the current model number "IMS105".

This heat release ice maker kit comes with a water inlet valve, an ice bin, the icemaker, and all the related hardware. This ice maker kit forms crescent shaped ice cubes, and is intended for use with refrigerators that have been manufactured since 1989/1990.

Sections of the IMS105 [Viewing 1 of 1]

$107.31

Ice Maker

This replacement ice maker mechanism does NOT come with a cover, a wire harness, or the mounting hardware. Must be ordered separately.

$2.70

Screw

Sold individually.

$2.70

Screw

This screw is sold individually.

$15.79

Water Fill Cup and Bearing

$37.57

Single Outlet Water Valve Kit

The water inlet valve is a solenoid-operated switch located at the bottom of the refrigerator. When it is energized by electrical power, water is released from the supply line thro...

$24.48

Thermostat with Clips

This part is also known as the cycling thermostat and this bi-metal device controls the activation of the icemaker ejection cycle.

$48.50

Ice Bucket

Holds the ice when it's released by the icemaker.

$2.70

Inlet Hose Gasket

$3.96

Compression Nut

$21.43

Ice Stripper

This part strips ice from the icemaker mold during the ejection cycle to prevent ice pieces from falling back into the mold.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 493 of 502 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 201 of 272 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 62 of 75 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more