IM115 Uni Ice Maker - Instructions

Steve from ORANGE, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

16 of 20 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ice maker would not make ice

un plug fridge. removed ice maker from fridge. loosen 2 mounting screws. lift unit in slots to get over heads of screws. unplug wire harness. remove cover. remove 3 screws from control housing. remove 2 motor mounting screws. unplug motor wires from switches w/needle nose. installation is the reverse. plug in fridge turn on icemaker. takes 10 to 15 min to start to cycle.
easy and cheaper than new fridge or ice maker

Parts Used:

paul from traer, IA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

16 of 22 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice maker was not making ice

I replaced the solenoid first because the ice maker was not getting water. After replacing the solenoid valve, I waited about 1/2 an hour, still no water. So, I ordered a replacement ice maker. I then installed the replacement ice maker, waited a 1/2 an hour, still no water. Then, I waited overnight. Yeah, ice! WORD OF ADVICE. WAIT OVERNIGHT TO SEE IF THE ICE MAKER CREATES ICE. Not sure how long a cycle takes, but it's longer than you would think. Hope your installation is a success!

Parts Used:

Jeffrey from Indianapolis, IN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

9 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice maker failed

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

Parts Used:

Mary from SOUTH LYON, MI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice maker stopped working

Took off old part and installed new part

Parts Used:

Fred from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

11 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ice maker quit making ice

I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the process for the install. It took about 25 minutes and i was back making ice.

Parts Used:

Barry from Middletown, DE
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original Ice Maker quit working.

Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

Parts Used:

Gary from Azle, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

my old ice maker leaked at the bottom

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

Parts Used:

harry from terre haute, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water Valve was leaking water and not making ice

I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.

Parts Used:

timothy from georgetown, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

13 of 28 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I replaced the icemaker

I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!

Parts Used:

Michele from Smithfield, UT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ice maker stopped working (Very oxidized residue)

I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.

Parts Used:

Robert from Woodstock, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

8 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The water valve for the ice maker was bad

Pulled the refrigerator out from the wall. Then unplugged it took my nutdriver with a1/4" socket on it and took out the screws from the cardboard back on the bottom of the refrigerator. Then I removed the two screws holding the water valve on. Then I unscrewed the supply water line from the main water inlet valve. Then I removed the outlet waterline going to the ice maker from the water valve. Then I reversed the procedure to put it back together. Hooked up the main water line and turned the water valve on for the water to flow to the valve at first nothing happened had to wait for a couple of hours for everything else to get to the right temperature before the ice maker would start making ice.

Parts Used:

frank from GRAND ISLAND, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace ice maker which was splashing water

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

Parts Used:

John from PHOENIX, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Warter valvr cracked

It was real easy but I still have problem making ice cubs
Fell problem is in the ice maker went it dose make cubs they don,t dump

Parts Used:

Louis from Damascus, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ice maker went bad

take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.

Parts Used: