Models > ICNT22F93A (5B78A)

ICNT22F93A (5B78A) Admiral Refrigerator - Overview

Get Parts and Repair Help for ICNT22F93A

If you know the refrigerator repair part you need, you can browse the list of all parts on the ICNT22F93A, or you can search by name or part description. You can also find your part by where it is located on the ICNT22F93A by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ICNT22F93A parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.70

Retaining Ring

This metallic retaining ring is less than an inch in diameter. It is made entirely of metal.

$2.70

Screw

This screw is sold individually.

$2.07

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.70

SCREW

Sold individually.

$4.70

Compression Nut

This compression nut is used with the plastic water line of the icemaker assembly.

$7.96

Plastic Tubing

1/4" Plastic tubing, 8 1/2 feet long.

$2.70

Screw

This is screw is sold individually.

$18.11

Ice Bin Drive Ring

This part connects the ice auger to the motor through the bin.

$4.19

Inlet Hose Gasket

This high pressure inlet hose washer is black. It is an inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers.

$74.59

Cold Control Thermostat

This cold control thermostat has a temperature range from 37 degrees Fahrenheit to 27 degrees Fahrenheit and a capillary length of 29 iches. This cold control thermostat cycles on and off regularly to keep your refrigerator cold.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Thermostat ceased to function. Fridge very cold.

  • Customer: Paul from Millboro VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 27 of 35 people found this instruction helpful
I removed control knobs and a couple of screws and forced the assembly down enough to remove the old thermostat, and insert the new one. Lucky me it was a identical replacement item. Job took about an hour. read more

the ice/water actuator switch burnt out and was stuck on.

  • Customer: Jon from Nampa ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
Removed the rubber cover over the actuator switch. Used a screwdriver to remove the switch, disconnected the wires. I then removed the switch from the mounting bracket using a small philips head screw driver. Installed the new switch on the mounting bracket then installed the switch onto the freezer door. The only difficult part was installing the rubbe... read more

The threads on the yoke shaft stripped.

  • Customer: Steven from Crossville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 10 of 20 people found this instruction helpful
I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems. read more