Models > HTS22GBPBRWW > Instructions

HTS22GBPBRWW Hotpoint Refrigerator - Instructions

All installation instructions for HTS22GBPBRWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the HTS22GBPBRWW
121-135 of 140
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator and freezer drawer would not maintain set temperature

  • Customer: James from Bel Air MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.

Freezer iced up and frige too warm.

  • Customer: Lisle from Monterey TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I called a repair shop and they said the control bd. was bad. They replaced it and about 2 weeks later it happened again. They came out again and replaced the bd. under warranty. About a week later it happened again. This seemed like too much of a coincidence, so I looked around on the internet and found your site. The video showed how to replace the freezer safety thermostat which I ordered on Sunday and received on Tuesday. By then the coils were iced up again. I completed the repair in about half an hour. So far the old GE is working like new. Thanks for the help. I just wish I hadn't spent over $400 for incompetent repair people in the first place. Thanks again, you guys are great! By the way the part only cost about $17 including shipping.

The evaporator fan in the freezer compartment began making a loud noise.

  • Customer: Boyd from Rapid City SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

Fan not working. Fridge and Freezer not cool

  • Customer: Audie from Des Allemands LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
It was simple. Unpluged fan two screws remove from fan bracket unplug old fan replace with new one put fan in place out screws back plugged in fan then plugged in fridge fixed problem. And save a repair cost call out. A.J.

shelf brackets holding meat/cheese drawer cracked.

  • Customer: ELIZABETH from BOULDER CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed two brackets on each side (Had to buy the correct little screw driver) and screwed in the new ones.Easy!

LEFT SLIDE PAN BROKE OFF, NEEDED TO REPLACE IT

  • Customer: JULIA from WARWICK NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
REMOVE ENTIRE SHELF FROM REFRIGERATOR AND REMOVED BROKE, SET THE REPLACEMENT PART IN PLACE, SCREWED IT IN AND IT WORKED PERFECTLY, DONE INFIVE MINUTES. TOOK ME LONGER TO TAKE OUT THE SELF THAT TO DO THE REPLACEMENT.

condenser fan was noisy ( squeaking)

  • Customer: Bryan from Las Vegas NV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Not knowing anything about a refrigerator it was hard to find the source of the noise. Once I could isolate it we googled the appliance repair and found the video from Parts Select and the rest was a piece of cake. Saved a service call and bloated parts prices. Thank you Parts Select!!!

Freezer side has ice forming inside and refrigerator side is warm

  • Customer: James from Los Angeles CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1) Unplug refrigerator (2) Remove the freezer trays/racks (3) Remove freezer light bulb (4) Remove screws holding rear freezer panel (inside freezer) (5) Defrost condenser with hair dryer (6) Clean up the excess water (7) Cut 2 wires to defrost thermostat (8) Splice in new t-stat with electrical twist connectors (9) Wrap connectors with electrical tape to prevent any excess moisture from entering electrical connections (10) Clip new t-stat into place on tube (11) Screw rear freezer panel back in place (12) Screw light bulb in (13) Return trays/ racks (14) Plug in refrigerator

Fan motor was really loud and whining

  • Customer: Paul from Brooksville ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Empty the contents of the freezer.Take out the one shelf.Remove the plastic pieces covering the fan and evaporator removing 2 screws with the nut driver.Remove the metal back using the nut driver(2 screws)Remove the fan assembly from the back of the freezer.(4 screws)Remove the green ground wire from the fan assembly(1 screw) Take the fan assembly out of the freezer and remove the old fan(2 screws) and reinstall the new fan.Assemble the parts in the reverse order .Very simple and intuitive for anyone who is "handy" at all.

squealing noise and refrigerator was feeling warm

  • Customer: Michael from Hudson OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Without the video, I would have been lost. I pulled the entire bracket out of the refrigerator, but could not insert the tab and adjust the bracket back in place, so I removed the bracket and motor, inserted the main frame bracket then re-installed the motor, fan , grommets, bracket. It's working.

noise from the condebser fan moter

  • Customer: Guojie from Gainesville FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Just follow the instructions from the Youtube, the link to the video is included in the sheet coming with the part. It was easy to take the entire compartment out as instructed, however, after replace the old motor with the new one, it took more than 20 min to put the entire compartment back after trying different ways. It has been working greatly since it was repaired.

Refrigerator's Freezer section was warm and there was ice accumulating on the inside back panel.

  • Customer: Richard from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the interior shelves and set screw which holds the light cover in place. Next I removed the four screws that hold the back panel in place. Located the defrost thermostat and removed it from the aluminum tubing by unclipping it, just as it was illustrated in the repair video. Cut the wires and stripped the ends and then connected them to the ends of the new defrost thermostat. Connected them together with an 16-14 gauge crimp style end cap. Taped the entry point into the end cap to reduce moisture penetration. Reassembled the back panel, light cover and shelves.

Slide track on right side of chill tray, where it was held together, on the metal frame, the screw cracked the plastic.

  • Customer: Richard from Jamestown ND
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Went to Sears, where I bought the Fridge, they could not locate the part I needed, so I went on line, and found partselect.com, entered the proper information, found the part I needed fast, ordered the part, received it in two days time, I already had the old part off, so it took less than ten minutes to replace it with the new part, works great, the people at partselect.com were great, an if needed, I will gladly order from them again.

freezer and fridge parts had stopped cooling

  • Customer: Grace from Arlington TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions on your YouTube video exactly and it was a snap. By far the hardest part of the repair was to fit the back tab of the fan assembly in the tight slot on the way out. The result was immediate and like having a new refrigerator. I'm a 68-yo retired woman but thanks to you I now feel empowered -- will tackle next appliance repair with confidence. Thank you.

Unusual noise from freezer.

  • Customer: Vincent from Lyndhurst NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.
All Instructions for the HTS22GBPBRWW
121-135 of 140